5
. Bring 1/4”
water supply line
from source (See page 6)
to
cut opening
as shown in
Figure 2
. (page 9).
Bring water line through
grommet
in
rough-in-box
(See
Supply Detail
). Carefully slide
rough-In-box
as
shown into
cut opening
while gently pulling
water supply line
through
grommet
hole in
rough-in-box
pulling through excess
(approx. 18”). Secure
rough-in-box
to wall stud with
sheet rock
screws
. PURGE WATER LINE by running water through line to
clean any possible debris. Cut water line to length (approx. 3”)
inside
rough-in-box
and attach
male quick connector
.
(See
Male Connector Detail
) and
Figure 4
.
IMPORTANT:
Water line to brewer must be flushed and a filter installed.
Should debris clog brewer system ALL WARRANTIES VOID.
4.
Place
rough-in-box
on a towel or cardboard to protect
counter surface. Bring
power supply wire
from source
to cut opening as previously shown in
Figure 2.
Minimum
12-2 wire required. Be sure to have an additional length of
approximately 18” recommended at
rough-in-box
opening
for installation of box. Remove
power panel cover.
Install
strain relief
(not supplied) in hole. Run
power supply wire
through
strain relief
and secure
power supply wire
(See
Supply Detail, page 10
). Connect
power supply wires
to
power panel supply wires
and secure with
wire nuts
(See
Wiring Detail, page 10
). Connect
green
wire to
green
wire,
black
to
black
and
white
to
white
. Carefully
reinstall
power panel cover
. Be certain not to damage
wires or insulation.
See Figure 3.
11
12
BrEwEr INSTALLATION
BrEwEr INSTALLATION
6.
After
sheet rock screws
are in place, gently bend appropriate
tabs (long or short depending on wall thickness such as tile
or granite) as shown on all other areas to finish securing
rough-in box
to
wall
. Use pliers (if needed) to
bend/crimp
tabs
firmly to
wall
. Gently slide excess water line back through
grommet into wall cavity leaving top of connector a maximum of
3” above bottom of rough-in box. See
Figure 5
. and
Figure 6
.
Installation of Brewer
7.
Quick connector is valved at rough-in-box so water can be
turned on prior to connection to coffee maker. Place unit on
a towel or cardboard to protect counter surface. Place
BREW EXPRESS™
directly in front of
rough-in box
. Use
quick
connector
to connect
water supply line
from
BREW EXPRESS™
to
water supply line
from
rough-in-box
(See
Quick Connect Detail
).
Snap connectors together firmly. Turn on water,
check for leaks
prior
to final installation of
BREW EXPRESS™
. If leaking, turn off water,
tighten connections or reinstall
quick connector
. Turn water on
and check again. See
Figure 7
.
8. Gently slide the BREW EXPRESS™ into the rough-in-box.
Be careful not to damage water supply lines. A firm fit will
connect power from rough-in-box to the BREW EXPRESS™.
Use four mounting screws to secure BREW EXPRESS™
inside rough-in-box. Be careful not to damage counter top.
NOTE: Refer to OPERATION GUIDE for further instructions
before using BREW EXPRESS™.
WARNING:
Do not caulk or grout brewer to wall.
3" max
Figure 6
Quick Connect Detail
Figure 7
Figure 8
Figure 5
Supply Detail
Wiring Detail
Male Connector Detail
All electrical wires and connections MUST be tucked
neatly and completely inside POWER PANEL COVER
without any exposed wiring inside rough-in box. It is
advised you contact a qualified electrician.
Figure 4
