MODEM SETTING
(TEXT MESSAGE CONNECTION)
37
TextMessageSett.
Alarm GSM1 nr
Alarm GSM2 nr
Device ID
MessageCentreNr
PIN-code
Modem type
Telephone nr.
Change
PIN-code
Change
----
Modem type
Falcom
Nokia/Siemens
Ouman/Fargo
Press the
button to move the cursor to "Change”.
Press
. "O” blinks.
Write the telephone number using the text editor.
You can move forward or backward in the character
OK
Give a telephone number that the regulator automatically sends a text
message to about an alarm in the event of an alarm. At first the alarm
message is only sent to the GSM number 1. If the alarm is not
acknowledged from this number, after five minutes the regulator sends a
new alarm to both the GSM 1 and 2 numbers.
The regulator can be given a device ID, which functions as the device's
secret password and address information. The device ID can be freely
labeled. The device ID is always written in front of the key word when
using the GSM to communicate with the regulator.
Telephone nr.
Change
Device ID
Not in use
In use
0000
Installing receivers for alarm messages:
Device ID:
Directions for entering the
maintenance mode are on page 19.
Special mainten.
Rstore settings
Settings
Meas. 6 setting
Meas. 11 setting
Dig1 selection
Dig2 selection
Dig3 selection
LON initaliz
Net measurement
TextMessageSett.
row with the
or button. Confirm the number by pressing
, then the
same number that you selected will blink in the next space. Whichever has
been selected last can be deleted by pressing
. If you press the
button for a while, the number will be deleted and the number that was
previously fed will remain in effect. When you are ready, press
for a
while (over 2 secretary.).
-
+
OK
ESC
ESC
OK
Move the cursor to "In use”. Press
. "0" blinks.
Write a device ID that has a max. of 4 characters.
The text editor has the letters A…Z and the numbers
0…9. You can move forward or backward in the
character row by pressing the
or
button.
Confirm the character by pressing
.
Give the operator-specific message center number
with
or
button. Confirm by pressing
.
Give the SIM card's PIN. The regulator will not
initialize the GSM modem before the PIN code is
installed. The SIM card has to be put in the GSM
telephone to change the modem's PIN. When you
have changed the PIN, install the SIM card back in
the modem.
203GT is compatible
with Falcom A2D, Nokia 30,Siemens M20T, Fargo
Maestro 20 and 100 Lite and Ouman modems.
OK
OK
OK
+
-
Installing the number for the message center:
+
-
Installing the modem's PIN for the regulator:
Selecting the modem type:
In order to communicate via text messages, the controller must be
connected to a GSM modem (optional equipment). The modem comes with
an adapter cable equipped with D-connector that is used to connect the
Modem to the controller. The controller's strip connector B-D space is
connected with a jumper wire.
GSM modem connection is done in start functions. The controller
automatically initializes the GSM modem in two hour intervals. This prevents
the GSM from becoming disconnected in the event of a power failure.
The modem is not on. Connect the modem to the network device.
The power is on but the modem is not ready to use. Inspect the following:
1. 203GT has the same PIN code as the GSM modem's SIM card PIN code.
2. Perform the start-up function. To start-up, move to Start function. Press OK. Exit with
ESC without changing settings.
The modem is ready to use.
The modem sends or receives messages. If a message does not come from the controller,
check the text message you have sent to see that the device ID and keyword have been
written correctly. Also check that the 203GT controller has the operator's message centre
number of the GSM connection you have in use. The factory setting is a Saunalahti
connection.
Guide for Ouman/Fargo modem connection and initialization:
Jumper
wire
Green
B
C
D
A
Y
ellow
Brown
Modem
connection
wire
LED is not on:
LED is on:
LED blinks slowly:
LED blinks rapidly:
Modem mode/ instructions
LED indicator light
37
Modem
Network device
