Laminex Metaline Manual Download Page 10

Page: 10 / 24

3.1.2 Fabrication Type – Folded External Corners

Preferred Method:

For fabrications where the Metaline is folded outwards to give a 270° seamless fold
around the outside corner of a kitchen, the following sequence is observed:

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

Some core must remail in

routered channel (maximum

1mm)

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

Some core must remail in routered

channel (maximum 1mm)

X - 6mm

Y - 6mm

X - 6mm

Back Face

Front Face

Y - 6mm

Back Face

Front Face

X + 6mm

Back Face

Front Face

Y + 6mm

Back Face

Front Face

X - 6mm

Y - 6mm

Back Face

Double Sided Tape

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Back Face

Front Face

X + 6mm

Y + 6mm

Back Face

Front Face

Double Sided Tape

Some core must remail in routered channel

(maximum 1mm)

1. Measure the external dimensions

of the corner:

2. Allowance is made for the panel

fold in the measurement as per
below:

3. Panels are routed using a 135°

V bit behind the section to be
folded to allow for the panel to be
bent, giving the following finished
fold:

4. The installed section will look like:

Summary of Contents for Metaline

























Search results

Summary of Contents for Metaline

Reviews:

Related manuals for Metaline

Brands by name

Popular brands

Laminex Metaline, Manual

Search results

Summary of Contents for Metaline

Reviews:

Related manuals for Metaline

Brands by name

Popular brands