Lakeview Fleur-de-lis Manual Download Page 9 | Manualshive

Page: 9 / 19

background image

9

5.

Attach 3 – Double End Studs (NN) and 3 - M8 Washers (OO)

to the top of the Head Assembly (C). Tighten the studs with the
Wrench (HH).

Hardware Used

:

6a. WARNING: Remove protective cover on reflector
panels/cap before assembling.

Note: If necessary for proper alignment of reflector assembly,
loosen each bolt prior to further assembly and re-tighten
after sections are aligned.

6b.

Slide 2 Reflector Panels (A) together. Insert 1 – M6x10 Screw (KK).

Slide 1 – M6 Washer (PP) over the threaded end of the screw and
then loosely secure with 1 – Cap Nut (LL). Repeat with other
screws/washer/cap nuts.

ASSEMBLY

5

6a

6b

«
...
7
8
9
10
11
...
»

Summary of Contents for Fleur-de-lis




















Reviews:

No comments

Related manuals for Fleur-de-lis

Brand: Lasko Pages: 4

Brand: Garantia Pages: 2

Brand: Paloma Pages: 28

Brand: Swann Pages: 14

Brand: pyromaster Pages: 16

Brand: Warmtec Pages: 60

Brand: Wijas Pages: 12

SL MINITHERM DNLA

Brand: Intertec Data Systems Pages: 8

Brand: ElectrIQ Pages: 23

DHE?18 SLi 25 A

Brand: STIEBEL ELTRON Pages: 22

Brand: PARAGON OUTDOOR Pages: 19

Brand: Mex Pages: 2

Brand: DuraHeat Pages: 20

Brand: Calienta Pages: 29

Brand: Warm Tech Pages: 24

Brand: Sealey Pages: 3

IGUANA CIRCO Wall

Brand: Jaga Pages: 2

Sovelor AERO110

Brand: Dantherm Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands