background image

 

15 

 

 
 
6. Once the pilot is lit, continue to depress the control knob for 
30 seconds. 
7. If the pilot does not stay lit, repeat steps 4-6. 
8. If after repeating steps 4-6 unit does not light, then: 
 

* Push in control knob and turn counter clockwise to PILOT. 

 

* As you are depressing the control knob, place stick lighter into 

 

    the viewing hole on the emitter screen to manually light 

            the pilot. 

NOTE

: If pilot fails to remain lit, all valves should be closed and a waiting 

period of at least 5 minutes should pass before attempting to re-light. 
 
9. Push in and turn the control knob counterclockwise to the LO position. 
To increase the flame, push in and turn the control knob counterclockwise 
to the HI position. 

If you experience any ignition problems, please consult “Troubleshooting” on page 18. 

Caution

: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the   

Burning of oils used in the manufacturing will appear. Both smoke and odor will dissipate after 
approximately 30 minutes. The heater should NOT produce thick black smoke. 

Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, 

turn the control knob CLOCKWISE to the PILOT position. Then turn the control knob to the desired 

level (Lo to HI).

 

 
 
 
 
 
 
 
 

When Heater is ON

Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display 
tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an 
obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow 
flame is detected, turn off heater and consult “Troubleshooting” on page 18. 

 
Re-Lighting

Note

: For your safety, control knob cannot be turned OFF without first depressing the control knob and then 

rotating to OFF. 

1. Turn control knob to OFF. 
2. Wait at least 5 minutes to allow gas to dissipate before re-lighting. 
3. Repeat the “Lighting” steps listed above. 

 
 
 
 
 
 

Shut Down

1. Turn control knob clockwise to PILOT. (Normally, burner will make a slight popping noise when extinguished). 
Burner will extinguish but PILOT will remain on. 
2. To extinguish PILOT, depress control knob and continue to turn clockwise to OFF position. 
3. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use. 

NOTE

: After use, some discoloration of the emitter screen is normal. 

 
 

 
 
 
 
 

 

 

OPERATING INSTRUCTIONS 

 

Summary of Contents for Fleur-de-lis




















Reviews: