background image

 

Product Service 1-800-522-7658 

Original instructions 

 
 
 
 
 
 
 
 

C

HAPTER 

2

 

P

REREQUISITES 

 

Before you install your Stoppering Tray Dryer, you need to prepare your site for 
installation.  The Stoppering Tray Dryer will mount on top of a FreeZone 6, 12 or 
18 liter Console Freeze Dryer.  Carefully examine the location where you intend 
to install your Stoppering Tray Dryer.  You must be certain that the area is level 
and of solid construction.  An electrical source must be located near the 
installation site. 
 
Carefully read this chapter to learn: 
 

 

Electrical supply requirements. 

 

Vacuum pump requirements. 

 
Refer to 

Appendix C: Specifications

 for complete Stoppering Tray Dryer electrical 

and environmental conditions, specifications and requirements. 
 
Refer to the User’s Manual for the FreeZone Console Freeze Dryers for complete 
electrical and environmental conditions, specifications and requirements. 

Electrical Requirements 

 

115V models   

o

 

20 Amp dedicated single phase circuit. 
 

 

o

 

Properly grounded receptacle for NEMA 
5-20P plug.     
 

 

230V models 

o

 

15 Amp dedicated single phase circuit.  

o

 

Properly grounded receptacle that matches the plug supplied with 
the unit, (230V models are supplied with one of the following 
plugs): 

 
 
 

US 

NEMA 5-20P 

Summary of Contents for FreeZone 794801 Series





















































Reviews: