Laars mascot ft MFTHW Page 62 Installation And Operation Instructions Manual Download

Page: 62 / 96

LAARS Heating Systems

Page 60

5.7 Installer Mode

Installer Mode.

These changes are to be made only by a qualified technician.

Index

Numbers

Parameter

Description

1: EH

Error history up to 10

Check last 10 error codes (E0 - E9)

2: cE

Delete Error history

Select “ON” to delete error code history

Range: ON or OFF,Default OFF

3: In

System initialize

Select “ON” to reset to factory setting,Default OFF

4: OH

Maximum Outdoor

Temperature

When used with an outdoor sensor, sets the maximum outdoor design

temperature for the system design. Warm weather shut down will

disable the appliance if the programmed outdoor temperature is ex-

ceeded. Maximum outdoor temperature must be set at least 9°F above

the minimum outdoor temperature. Range: (Minimum Outdoor Tempera-

ture + 9°F) to 110°F , Default 68°F

5: OL

Minimum Outdoor

Temperature

Sets the minimum outdoor design temperature for the system. Minimum

outdoor temperature must be set at least 9°F below the maximum

outdoor temperature.

Range: -4°F to (Maximum Outdoor Temperature - 9°F), Default 5°F

6: cH

Maximum Supply

temperature

Sets the maximum design supply temperature based on the minimum

outdoor design temperature. Maximum supply temperature must be set

at least 9oF above the minimum supply temperature. Range: (Minimum

Supply Tempe 9°F) - 180°F, Default 180°F

To c hange any of the Installer Parameters,

Start by turning

OFF

the Power

to the

Display Control.

Then, with the power OFF, Press and HOLD (more than 5 seconds) the Button B

to get into the Installer Mode.

Rotate Dial E until you find the Installer Parameter (full list on facing page) that you wish to change. Tap Dial E

to enter that Parameter.

Adjust to the setting that you require and then press (tap) Dial E to save and to Exit.

Finish by pressing button B

Summary of Contents for mascot ft MFTHW

































































































Search results

Summary of Contents for mascot ft MFTHW

Reviews:

Related manuals for mascot ft MFTHW

Brands by name

Popular brands

Laars mascot ft MFTHW, Installation And Operation Instructions Manual

Search results

Summary of Contents for mascot ft MFTHW

Reviews:

Related manuals for mascot ft MFTHW

Brands by name

Popular brands