background image

Page 18

LAARS Heating Systems

4. This appliance is equipped with an ignition

device which automatically lights the burner.
Do not try to light the burner by hand.

5. Remove front door.
6. Turn gas shutoff valve clockwise

to “off”.

Handle will be horizontal, do not force.

7. Wait five (5) minutes to clear out any gas. Then

smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety
information above (to the left) on this label. If
you don’t smell gas, go to the next step.

8. Turn gas shutoff valve counterclockwise

to

“on”. Handle will be vertical.

9. Replace front door.
10. Turn on all electric power to appliance, depress

on/off button on control panel, depress black
button on top of control panel.

11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the

instructions “To Turn Off Gas To Appliance”
and call your service technician or gas supplier.

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING

If you do not follow these instructions exactly, a fire or explosion

may result, causing property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition

device which automatically lights the pilot. Do

not

 try to light the pilot by hand.

B. BEFORE OPERATING smell all around the

appliance area for gas. Be sure to smell next to
the floor because some gas is heavier than air
and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's
instructions.

• If you cannot reach your gas supplier, call

the fire department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will
notpush in or turn by hand, don’t try to repair it,
call a qualified service technician. Force or
attempted repair may result in a fire or
explosion.

D. Do not use this appliance if any part has been

under water. Immediately call a qualified
service technician to inspect the appliance and
to replace any part of the control system and
any gas control which has been under water.

OPERATING INSTRUCTIONS

1. STOP! Read the safety information above on

this label.

2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if

service is to be performed.

3. Remove front door.

4. Turn gas shutoff valve clockwise

to “off”. Do

not force.

5. Replace front door.

Combination

Gas Control

Gas Shutoff

Valve

Summary of Contents for EBP0110









































Reviews: