background image

TABLE OF CONTENTS

GENERAL INFORMATION �������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 1

ENTRY DEVICE MOUNTING TEMPLATES ������������������������������������������������������������������������������������������������������������������������������������������������ 3

3000 AND 3715 ENTRY DEVICE ���������������������������������������������������������������������������������������������������������������������������������������������������������������� 4

3035 & 3125 ROUND ENTRY DEVICE ������������������������������������������������������������������������������������������������������������������������������������������������������� 5

  •  Swingbolt instructions
  •  Dead bolt instructions

3710 ANGULAR ENTRY DEVICE ��������������������������������������������������������������������������������������������������������������������������������������������������������������� 7

  •  Additional instructions 3710 keypad replacement

3750, 3750-K, 3750KE, & 3190 ENTRY DEVICE ��������������������������������������������������������������������������������������������������������������������������������������� 8

  •  Swingbolt instructions
  •  Dead bolt instructions

8130����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 10

2666 KNOB ASSEMBLY ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 11

Summary of Contents for 3000














Reviews: