GB
P.8
GB
P.9
GB
P.6
GB
P.7
B. INDOOR WEATHER STATION
1. Remove the battery cover. To do this, insert a solid object in
the space provided at the lower-central position of the battery
cover, then push up and pull out on the battery cover.
2. Observe the correct polarity, and install 3 AA batteries.
3. Replace the battery cover.
Note: Immediately after the batteries have been installed, the
LCD (Liquid Crystal Display) will flash. Within 15 seconds the
indoor temperature, indoor relative humidity, and the weather icons
(sun and clouds) will be displayed. If not, remove batteries for 10
seconds and reinstall. If the outdoor temperature is not displayed
within four minutes, remove batteries from both units, wait 30
seconds, and reinstall making sure to install batteries into the
remote temperature sensor first. The time will show 12:00 and
start searching for the WWVB signal. If it successfully receives
the time signal (usually at night), it will display the correct time
(default time-zone is Eastern). You will need to adjust the time
zone to match your local time.
PROGRAM MODE
Programming Note: If 15 seconds are allowed to pass, or the
SNZ/CH button is pressed during the programming mode, the unit
will confirm/set the last information entered-the display will stop
flashing and return to normal time-date readings. If you don’t leave
the program mode during the programming of sections III through
XI, you can advance to step 4 of the next program setting. If you
do leave the program setting (or want to program a specific setting)
follow each instructional step to program that setting.
I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS
The programming sequence and default (factory) settings are as
follows:
LCD Contrast
5
Time Zone
-5 (Eastern)
Daylight Saving Time
ON
Radio-controlled time reception
ON
12/24-hour time
12
Time - Hour
12
Time - Minute
:00
Year
2003
Month
1
Day
1
Snooze
10 minutes
Forecast Sensitivity
2
II. FUNCTION KEYS
The function keys are located on the front of the unit directly below
the LCD (Liquid Crystal Display).
III. SETTING THE LCD CONTRAST
1. Press and hold the SET button for 3 seconds.
2. “LCD” will show in the TIME LCD and the number setting will
flash.
Note: There are 8 LCD contrast levels to choose from ”Lcd 0" is
the lightest, and “Lcd 7” is the darkest.
3. Press and release the ALM/+ button to select the level you
desire.
4. Press and release the SET button to confirm and advance to
the Time Zone setting.
IV. TIME ZONE SETTING
1. Press and hold the SET button for 3 seconds.
2. “LCD” will show in the TIME LCD and the number setting will
flash.
3. Press and release the SET button again.
4. The time zone will flash in the DATE LCD.
5. Press and release the ALM/+ button to select your time zone.
Note: It is possible to select any time zone from -12 GMT to +12
GMT (for example to see the time in another country).
TIME ZONES
GMT
0
Atlantic
-4
EST
Eastern
-5
CST
Central
-6
MST
Mountain -7
PST
Pacific
-8
ALA
Alaska
-9
HAW
Hawaii
-10
6. Press and release the SET button to confirm and advance to
the Daylight Saving Time setting.
V. DAYLIGHT SAVING TIME (DST) SETTING
1. Press and hold the SET button for 3 seconds.
2. “LCD” will show in the TIME LCD and the number setting will
flash.
3. Press and release the SET button twice.
4. “DST” will appear in the DATE LCD and either “ON” or “OFF”
will flash in the TIME LCD.
5. Press and release the ALM/+ button to select DST on or off.
Note: “DST OFF” indicates that the feature is off and the WWVB
will not change times automatically. “DST ON” indicates that the
feature is on and the WWVB will change times automatically.
Note: Some locations (Arizona and parts of Indiana) do not follow
Daylight Saving Time, and should select “DST OFF”.
6. Press and release the SET button to confirm and advance to
the radio-controlled time on/off setting.
VI. RADIO-CONTROLLED TIME ON/OFF SETTING
1. Press and hold the SET button for 3 seconds.
2. “LCD” will show in the TIME LCD and the number setting will
flash.
3. Press and release the SET button three times.
4. “RCC” will appear in the DATE LCD and “ON” or “OFF” will
flash in the TIME LCD.
5. Press and release the ALM/+ button to select radio-controlled
time on or off.
6. Press and release the SET button to confirm and advance to
the 12/24-hour time setting.
VII. 12 OR 24 HOUR TIME SETTING
1. Press and hold the SET button for 3 seconds.
2. “LCD” will show in the TIME LCD and the number setting will
flash.
3. Press and release the SET button four times.
4. “12h” or “24h” will flash in the DATE LCD.
5. Press and release the ALM/+ button to select 12 or 24-hour
time format.
Note: When in the 12-hour format “P.M.” will appear to the left of
the hour in the time LCD between the hours of noon and midnight.
6. Press and release the SET button to confirm and advance to
the time setting.
