manualshive.com logo in svg

Kyocera Copystar CS-1635, Service Manual

The Kyocera Copystar CS-1635 is a reliable office copier known for its exceptional performance and user-friendly interface. Enhance your productivity with this versatile device by easily accessing its Service Manual. You can download the manual for free from our website, empowering you to troubleshoot and optimize its functionalities.

Share
Download
background image

2HA/2HB

1-4-17

C3100

Scanner carriage problem

The home position is not correct when 
the power is turned on or copying the 
document placed on the contact glass.

Poor contact of the 
connector termi-
nals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective scanner 
home position 
switch.

Replace the scanner home position switch.

Defective engine 
PWB.

Replace the engine PWB and check for cor-
rect operation.

Defective scanner 
motor.

Replace the scanner motor.

C3200

Exposure lamp problem

Non-lighting of the exposure lamp is 
detected at the beginning of copying.

Poor contact of the 
connector termi-
nals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective exposure 
lamp or inverter 
PWB.

Replace the exposure lamp or inverter 
PWB.

Defective engine 
PWB.

Replace the engine PWB and check for cor-
rect operation.

Incorrect shading 
position.

Adjust the position of the contact glass 
(shading plate). If the problem still occurs, 
replace the scanner home position switch.

C3300

Optical system (AGC) problem

After AGC, correct input is not obtained 
at CCD.

Insufficient expo-
sure lamp luminos-
ity.

Replace the exposure lamp or inverter 
PWB.

Defective engine 
PWB.

Replace the engine PWB and check for cor-
rect operation.

Incorrect shading 
position.

Adjust the position of the contact glass 
(shading plate). If the problem still occurs, 
replace the scanner home position switch.

Defective CCD 
PWB.

Replace the ISU.

C4000

Polygon motor synchronization prob-
lem

The polygon motor does not reach the 
stable speed within 20 s of the START 
signal turning on.

Poor contact in the 
polygon motor con-
nector terminals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective polygon 
motor.

Replace the LSU.

Defective engine 
PWB.

Replace the engine PWB and check for cor-
rect operation.

C4010

Polygon motor steady-state problem

The polygon motor rotation is not stable 
for 5 s after the polygon motor rotation 
has been stabilized.

Poor contact in the 
polygon motor con-
nector terminals.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective polygon 
motor.

Replace the LSU.

Defective engine 
PWB.

Replace the engine PWB and check for cor-
rect operation.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Datecs PP-55 User Manual preview
PP-55
Brand: Datecs Pages: 73
Datamax H-Class Quick Start Manual preview
H-Class
Brand: Datamax Pages: 12
Datamax E-Class Mark II Maintenance Manual preview
E-Class Mark II
Brand: Datamax Pages: 40
Datamax E-class E-3202 Quick Reference Manual preview
E-class E-3202
Brand: Datamax Pages: 46
Canon S 200 User Manual preview
S 200
Brand: Canon Pages: 198
Oki MC160N User Manual preview
MC160N
Brand: Oki Pages: 268
Oki LE810DT Manual De L'Utilisateur preview
LE810DT
Brand: Oki Pages: 54
Oki LE810DT Guías Del Usuario Manual preview
LE810DT
Brand: Oki Pages: 54
Oki MB460MFP Manual Do Usuário preview
MB460MFP
Brand: Oki Pages: 202
Oki MB460MFP Manual De L'Utilisateur preview
MB460MFP
Brand: Oki Pages: 201
Oki ES2232a4 User Manual preview
ES2232a4
Brand: Oki Pages: 103
Oki ES3037 User Manual preview
ES3037
Brand: Oki Pages: 256
Oki B710dn Hardware Manual preview
B710dn
Brand: Oki Pages: 2
Oki B710dn Material Safety Data Sheet preview
B710dn
Brand: Oki Pages: 36
Oki B6500 Series Guia Del Usuario De Redes preview
B6500 Series
Brand: Oki Pages: 63
Oki B6500 Series Customer Support Information preview
B6500 Series
Brand: Oki Pages: 28
Oki B6500 Series Service Manual preview
B6500 Series
Brand: Oki Pages: 616
Oki B411d Safety Information Manual preview
B411d
Brand: Oki Pages: 32

Brands by name

Popular brands

Load more brands