Kyocera Copystar CS-1635 Service Manual Download Page 164 | Manualshive

Page: 164 / 244

background image

2HA/2HB-2

1-6-2

1-6-2

Adjustment-free variable resistors (VR)

The variable resistors listed below are set at the factory prior to shipping and cannot be adjusted in the field.
High-voltage PWB: VR201, VR202, VR301
Drum unit zener PWB: VR1

1-6-3

Remarks on PWBs replacement

Confirm the version of the firmware and upgrade the version in up-to-date state when replacing PWBs.
When replacing the engine PWB or main PWB, remove the EEPROM from the engine PWB or main PWB that has been
removed and then reattach it to the new engine PWB or main PWB.

Figure 1-6-2

1-6-4

Upgrading print system firmware

It is necessary to have GDI printer driver installed.

Upgrade using PC/USB

1.

[Start]

→

[Setting]

→

[Printer & FAX]

→

find “Kyocera KM-1635KX”

2.

Click right button of the mouse to select [Shared] and Shared name should be KM1635

3.

Open MSDOS (Command prompt) and type c:\>hostname (EX: aaaa)

4.

Then type c:\>net use lpt2 \\aaaa\KM1635

5.

Printer will be applied to lpt2

6.

Check to see if this is done correctly. Type c:\>net use

7.

On the screen, “OK LPT2 \\aaaa\KM1635 Microsoft Windows Network” is displayed

8.

Finish setting

9.

When you want to send the file, type c:\>copy /b file_name lpt2

Upgrade using DIMM

1.

Make sure the main switch is turned OFF.

2.

Remove Printer Board from the main unit, insert the DIMM (P/N: 303KC94020) into the slot in Printer Board and
change the jumper switch (SW1) position on Printer Board to "1-2".

3.

Insert the Printer Board into the main unit.

4.

Turn the main switch ON and wait for 90 seconds. (*1)

5.

After more than 90 seconds is passed, turn OFF the main switch. (*2)

6.

Remove Printer Board from the main unit and remove DIMM from Printer Board, then, return the jumper switch to
its original position "2-3".

7.

Insert Printer Board into the main units.

(*1) If pressing printer key in the main unit without turning OFF in about 2 minutes after the download is complete,

"Please power off/on. A0240" will be displayed. But it is not error. (In that case, please start over from procedure 5.)

ATTENTION

(*2) No beep will sound when the Printer Board firmware upgrade is complete. (A beep will sound when the main unit

firmware upgrade is complete.)
If turning OFF the main switch without waiting 90 seconds, "A240" will be displayed when the main switch is turned
ON. In this case, Please try again from the procedure 1.

EEPROM

EEPROM

«
...
162
163
164
165
166
...
»

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Brand: Oki Pages: 2

Brand: Oki Pages: 52

Brand: Oki Pages: 117

Brand: Oki Pages: 45

Brand: Oki Pages: 112

Brand: Oki Pages: 115

Brand: Oki Pages: 2

Brand: WaxJet Pages: 131

Brand: NCR Pages: 36

Brand: NCR Pages: 206

Brand: NCR Pages: 138

Brand: Oki Pages: 17

Brand: Oki Pages: 12

Brand: Oki Pages: 30

Brand: Oki Pages: 391

Brand: Oki Pages: 2

VarioPrint 1055

Brand: OcÃ© Pages: 194

Brand: Oce Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands