Kyocera Copystar CS-1635 Service Manual Download Page 49 | Manualshive

Page: 49 / 244

background image

2HA/2HB

1-3-17

U060

Adjusting the scanner input properties
Description

Adjusts the image scanning density.

Purpose

Used when the entire image appears too dark or light.

Method

Press the start key.

Setting

1. Change the setting using the zoom +/- keys.

Increasing the setting makes the density lower, and decreasing it makes the density higher.

2. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, test copying from an original is available.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Caution

The following settings are also reset to the initial values by performing this maintenance item:
Exposure density gradient set in maintenance mode (U093)
Exposure set in the copy default item of the copier management mode

U061

Turning the exposure lamp on
Description

Turns the exposure lamp on.

Purpose

To check the exposure lamp.

Method

1. Press the start key. "on" appears.
2. Press the start key. The exposure lamp lights.
3. To turn the exposure lamp off, press the stop/clear key.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

U063

Adjusting the shading position
Description

Changes the shading position.

Purpose

Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned. This
is due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be
changed so that shading is possible without being affected by the flaws or stains.

Method

1. Press the start key.
2. Change the setting using the zoom +/- keys.

Increasing the setting moves the shading position toward the machine left, and decreasing it moves the
position toward the machine right.

3. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, test copying from an original is available.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

Description

Setting range

Initial setting

Image scanning density

0 to 23

12

Description

Setting range

Initial setting

Change in value per step

Shading position

-5 to 5

0

0.17 mm

«
...
47
48
49
50
51
...
»

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Brand: IDStation Pages: 18

Brand: Cashino Pages: 74

Brand: Oki Pages: 120

Brand: Kyocera Pages: 2

Brand: Tally Pages: 266

Brand: UVP Pages: 22

Brand: LulzBot Pages: 3

Brand: SPRT Pages: 21

Brand: FujiFilm Pages: 28

Brand: Triumph Adler Pages: 202

All in One Printer

Brand: Epson Pages: 210

aculaser cx37 series

Brand: Epson Pages: 261

AL-MX200 Series

Brand: Epson Pages: 410

AcuLaser CX29DNF

Brand: Epson Pages: 456

AL-MX300 Series

Brand: Epson Pages: 2

workforce wf-2630

Brand: Epson Pages: 256

WorkForce Pro WP-4595 DNF

Brand: Epson Pages: 2

WorkForce WF-2540

Brand: Epson Pages: 283

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands