Kyocera Copystar CS-1635 Service Manual Download Page 39 | Manualshive

Page: 39 / 244

background image

2HA/2HB

1-3-7

U005

Copying without paper
Description

Simulates the copy operation without paper feed.

Purpose

To check the overall operation of the machine.

Method

1. Press the start key.
2. Select the item to be operated using the exposure adjustment keys.

3. Press the interrupt key.
4. Set the operation conditions required. Changes in the following settings can be made.

Paper feed locations
Magnifications
Number of copies: continuous copying is performed when set to 250.
Copy density
Keys on the operation panel other than the energy saver (preheat) key

5. To control the paper feed pulley, remove all the paper in the drawers, or the drawers. With the paper

present, the paper feed pulley does not operate.

6. Press the start key.

Copy operation is simulated without paper under the set conditions.

7. To stop continuous operation, press the stop/reset key.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

Display

Operation

P

Only the copier operates.

P-d

Both the copier and DP operate.

«
...
37
38
39
40
41
...
»

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Brand: IBM Pages: 102

Brand: Datecs Pages: 29

Brand: Wasp Pages: 2

Brand: Oki Pages: 24

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

Accel a Writer 812

Brand: Xante Pages: 312

WorkCentre 7830

Brand: Xerox Pages: 12

Brand: Oakton Pages: 8

ThermalTronix TT-1025EX-MIL

Brand: Intellisystem Pages: 11

Brand: Ricoh Pages: 88

Brand: Magicard Pages: 31

DocumentCentre C400 Series

Brand: Xerox Pages: 97

Brand: Canon Pages: 436

Pixma TS8700 Series

Brand: Canon Pages: 589

Brand: Canon Pages: 34

WorkCentre 3315

Brand: Xerox Pages: 18

WORKCENTRE 7755

Brand: Xerox Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands