KYMCO G-DINK 300i Service Manual Download

Page: 7 / 247

1. GENERAL INFORMATION

1-4

G-DINK 300i

After operation, terminal caps shall be

installed securely.

When taking out the connector, the lock on

the connector shall be released before
operation.

Hold the connector body when connecting

or disconnecting it.

Do not pull the connector wire.

Check if any connector terminal is bending,

protruding or loose.

The connector shall be inserted
completely.

If the double connector has a lock, lock

it at the correct position.

Check if there is any loose wire.

Before connecting a terminal, check for

damaged terminal cover or loose negative
terminal.

Check the double connector cover for
proper coverage and installation.

Insert the terminal completely.

Check the terminal cover for proper
coverage.

Do not make the terminal cover opening

face up.

Secure wire harnesses to the frame with

their respective wire bands at the
designated locations.

Tighten the bands so that only the

insulated surfaces contact the wire
harnesses.

After clamping, check each wire to make

sure it is secure.

Confirm
Capacity

Summary of Contents for G-DINK 300i
























































































































































































































































Search results

Summary of Contents for G-DINK 300i

Reviews:

Related manuals for G-DINK 300i

Brands by name

Popular brands

KYMCO G-DINK 300i, Service Manual

Search results

Summary of Contents for G-DINK 300i

Reviews:

Related manuals for G-DINK 300i

Brands by name

Popular brands