KWS Electronic VAROS 109 Page 4 Manual Download | Manualshive

Page: 4 / 60

background image

Chapter 1 - Notes on Safety and Use, Maintenance and Service

10911 V01.06

4

Chapter 1

Notes on Safety and Use, Maintenance and Service

1.1

Safety notes

This instrument is built and tested according to EN 61010-1 (protective measures for electronic
measuring instruments) with attached power cable.

Important!

This instrument may only be powered with the power cable originally delivered from

the

factory.

The instrument is in perfect working order upon leaving the factory. To ensure safe and proper
operation, and to keep the instrument in a safe condition, the user must observe all the notes and
warnings contained in this instruction manual.

The instrument has protection class IP20 in accordance with EN 60529.

Discharges across the plug connector can damage the instrument. Protect the instrument from
electrostatic discharge when handling and operating it.

The maximum external voltage that van be applied to the measuring receiver’s RF input is 24

V. A

higher voltage may destroy the input circuits.

Do not cover the ventilation slots on the instrument. Covering the slots can result in reduced air
circulation in the instrument, which can cause heat build-up and overheating of the electronic
components.

Passage from the battery regulations (BattV)

This device contains a battery which incorporates hazardous substances. It must
not be disposed of I domestic waste. At the end of its working life it should be
disposed of only through the ESC customer service department or at a designated
collection point.

1.2

Usage Notes

The guarantee for a new instrument ends 12 months after delivery.

The guarantee is invalidated if the instrument is opened.

Sharp tools (e.g. a screwdriver) can damage the plastic glass in front of the TFT display, thus
destroying the TFT.

The contrast of the TFT display deteriorates at ambient temperatures below 5°C.

The TFT display does not reach maximum brightness for a few seconds after the instrument is cold-
started.

The instrument reaches full measurement accuracy after about 5 minutes of operation.

The use of wireless DECT phones and GSM phones close to the instrument can cause disturbances
and faulty measurements.

1.3

Maintenance

The instrument is maintenance-free.

«
...
2
3
4
5
6
...
»

Summary of Contents for VAROS 109





























































Reviews:

No comments

Related manuals for VAROS 109

Brand: M & I Instruments Pages: 2

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

Brand: Omega Pages: 170

Brand: CA.MI Pages: 68

Brand: JENCO Pages: 13

Brand: Ansul Pages: 24

Brand: ENDA Pages: 2

Brand: Heinrichs Pages: 31

Brand: Fluke Calibration Pages: 13

Brand: Agilent Technologies Pages: 198

Brand: Oberheim Pages: 41

Brand: Newton Pages: 112

Brand: DIALAB Pages: 20

CHEM2000-UV-VIS

Brand: Ocean Optics Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands