manualshive.com logo in svg

KWS Electronic VAROS 109, Manual, Page: 23 / 60

Share
Download
KWS Electronic VAROS 109 Manual Download Page 23

 

 

Chapter 6 - Measuring range

 

 

10911 V01.06 

23

 

6.5.3.1 Activation and Configuration 

The UNICABLE control is activated via 

LNB

 -> 

DiSEqC

 -> 

UNIC

. 

The first menu that appears allows users to choose between setting the SCR-ADR-BANK and setting 
the SCR-ADR (satellite channel router address). 
In the SCR-ADR menu, users can select the user band (UB) bandpass slot for the measuring 
receiver to use and edit the corresponding centre frequency. These parameters can be obtained from 
the data sheet of the UNICABLE unit being used. 
 

 

 

This figure shows the default settings with the following relationships: 
 
 

SCR-ADR0:= 1284 MHz 

SCR-ADR1:= 1400 MHz 

 

SCR-ADR2:= 1515 MHz 

SCR-ADR3:= 1632 MHz 

 

SCR-ADR4:= 1748 MHz 

SCR-ADR5:= 1864 MHz 

 

SCR-ADR6:= 1979 MHz 

SCR-ADR7:= 2095 MHz 

 

Note:  

Manufacturers have different methods for numbering the UBs. They are numbered either from 0 to 7 
or from 1 to 8. The physical address always goes from 0 to 7. For example, the lowest slot, which 
could also be marked as UB1 on the converter unit, can be activated by selecting SCR-ADR0 (UB1).

 

 
To change the settings displayed, proceed as follows: 
Use the 

Up 

and 

Down

 keys

 

to select the required SCR address. Then press the 

->

 key to access the 

following menu. 
 

 

Summary of Contents for VAROS 109





























































Reviews:

No comments