manualshive.com logo in svg

KWS Electronic VAROS 109, Manual

The KWS Electronic VAROS 109 user manual is available for free download on our website. This comprehensive manual provides step-by-step instructions on setting up and operating the VAROS 109. Enhance your product experience with our user-friendly manual, all conveniently accessible at manualshive.com.

Share
Download
background image

 Index

 

10911 V01.06 

58

 

Index 

 
12V power supply --------------------------------------------------------------------------------------------------------------- 11 
14/18 V – 22 kHz control ------------------------------------------------------------------------------------------------------ 19 

A

 

Accessing the analyzer -------------------------------------------------------------------------------------------------------- 29 
Acoustic level trend indicator ------------------------------------------------------------------------------------------------- 19 
Activating software options --------------------------------------------------------------------------------------------------- 54 
Activating the optical input ---------------------------------------------------------------------------------------------------- 45 
Activating the remote supply -------------------------------------------------------------------------------------------------  31 
Activation and Configuration ---------------------------------------------------------------------------------------------23, 26 
Analyzer --------------------------------------------------------------------------------------------------------------------------- 29 
Automatic recording of measurement sets ------------------------------------------------------------------------------- 56 

B

 

Battery management -----------------------------------------------------------------------------------------------------------  12 
Battery operation ---------------------------------------------------------------------------------------------------------------- 12 
BER measurement (bit error rate measurement) -------------------------------------------------------------------17, 18 
Botton tone (beeper) ----------------------------------------------------------------------------------------------------------- 53 

C

 

C band ----------------------------------------------------------------------------------------------------------------------------- 15 
Calibration -------------------------------------------------------------------------------------------------------------------------- 5 
Card menu ------------------------------------------------------------------------------------------------------------------------ 42 
Cleaning ----------------------------------------------------------------------------------------------------------------------------- 5 
Cleaning the fibre optic plug connection ---------------------------------------------------------------------------------- 46 
Clock ------------------------------------------------------------------------------------------------------------------------------- 52 
Common Interface -------------------------------------------------------------------------------------------------------------- 42 
Constellation diagram (Option) ---------------------------------------------------------------------------------------------- 50 
Contents ----------------------------------------------------------------------------------------------------------------------------- 1 
Control and connection elements, pin configurations -------------------------------------------------------------------- 9 
Cursor ------------------------------------------------------------------------------------------------------------------------------ 29 

D

 

DATA LOGGER -----------------------------------------------------------------------------------------------------------------  56 
Default setting ------------------------------------------------------------------------------------------------------------------- 52 
Deleting measurement sets from the device -----------------------------------------------------------------------------  57 
Disable memory protection ---------------------------------------------------------------------------------------------------  39 
DiSEqC ---------------------------------------------------------------------------------------------------------------------------- 19 
DiSEqC V1.0 control ----------------------------------------------------------------------------------------------------------- 20 
DiSEqC V1.1 control ----------------------------------------------------------------------------------------------------------- 20 
DiSEqC V1.2 control ----------------------------------------------------------------------------------------------------------- 21 
DiSEqC V2.0 control ----------------------------------------------------------------------------------------------------------- 22 
Display of MPEG video parameters ----------------------------------------------------------------------------------------  37 
DVB-S mode --------------------------------------------------------------------------------------------------------------------- 16 
DVB-S parameters-------------------------------------------------------------------------------------------------------------- 16 
DVB-S2 mode ------------------------------------------------------------------------------------------------------------------- 17 
DVB-S2 parameters ------------------------------------------------------------------------------------------------------------  18 
DVI output ------------------------------------------------------------------------------------------------------------------------ 11 
DVI Output ------------------------------------------------------------------------------------------------------------------------ 55 
Dynamic program switching --------------------------------------------------------------------------------------------------  37 

E

 

Erasing a memory location --------------------------------------------------------------------------------------------------- 39 
Erasing the memory ------------------------------------------------------------------------------------------------------------ 38

Summary of Contents for VAROS 109





























































Reviews:

No comments

Related manuals for VAROS 109

Major tech MT350 Instruction Manual preview
MT350
Brand: Major tech Pages: 8
Waltron 9072 User Manual preview
9072
Brand: Waltron Pages: 25
Medeli SP40A User Manual preview
SP40A
Brand: Medeli Pages: 14
Raymarine ST40 Wind Owner'S Handbook Manual preview
ST40 Wind
Brand: Raymarine Pages: 42
Orange Electronic P451 Manual preview
P451
Brand: Orange Electronic Pages: 21
DeltaOHM HD2011NMT Operating Manual preview
HD2011NMT
Brand: DeltaOHM Pages: 26
Balluff BML-S1G0-Q71 Series Condensed Manual preview
BML-S1G0-Q71 Series
Brand: Balluff Pages: 20
LEM EM4TII+ Manual preview
EM4TII+
Brand: LEM Pages: 33
ASCOM TEMS AUTOMATIC - 2 Brochure preview
TEMS AUTOMATIC - 2
Brand: ASCOM Pages: 12
Eno Scientific Well Watch 700 User Manual preview
Well Watch 700
Brand: Eno Scientific Pages: 47
Sagola Classic I 2 Instruction Manual preview
Classic I 2
Brand: Sagola Pages: 16
KEM RA-620 Operation Manual preview
RA-620
Brand: KEM Pages: 49
wtw Oxi 197i Operating Manual preview
Oxi 197i
Brand: wtw Pages: 63
Laserworld Rainbow RTI-Nano Series Manual preview
Rainbow RTI-Nano Series
Brand: Laserworld Pages: 25
Hanna Instruments HI 88703 Instruction Manual preview
HI 88703
Brand: Hanna Instruments Pages: 32
iDigit A570 Ambient Monitor Instruction Manual preview
A570 Ambient Monitor
Brand: iDigit Pages: 15
Mahr 25 ES Operating Instructions Manual preview
25 ES
Brand: Mahr Pages: 14
janitza MRG 512 PQ Flex Operation Manual preview
MRG 512 PQ Flex
Brand: janitza Pages: 9

Brands by name

Popular brands

Load more brands