SECTION II
Operation
P 2.1
A. OPERATING SEQUENCE:
(Figure 2.1)
The closer is ready to run when the closure is in
closing position, with both the power switch and the
run switch in the ”ON” position, and the ”READY”
light is on. When the closed bag and closure are re-
moved from the closure track, the machine com-
pletes the closing cycle placing the next closure in
the closing position. The machine is again ready for
the next bag. During the completion of the closing
cycle the ”READY” light will go off momentarily.
If no closure is available to move into the closing
position, the machine will continue to cycle and the
”READY” light will flash repeatedly until the run
switch is turned to the ”STOP” position.
The 086B Model 700P operating sequence is differ-
ent from the other 086B Models in that it prints,
feeds, and breaks off the closure continuously while
the run switch is in the “RUN” position. The closer
will stop cycling when the run switch is in the “STOP”
position or the last closure is manually removed from
the track assembly. When a new strip of closures is
inserted into the track and the “RUN” switch is in the
run position, a press of the green button, located on
the side access cover, will begin the continous cycle
of the machine.
THE PRINTER COVER MUST ALWAYS BE IN THE
CLOSED POSITION WHEN OPERATING THE
CLOSER.
The power switch and light must be off to cut
off power to the two sensor switches. Utilizing
the power switch instead of the run switch may
result in the machine not stopping in the neutral
position as required for loading the closure
strip. Use the power switch when clearing the
machine of debris or preforming minor service
work.
1. Plug in the closer.
2. Press the power switch to ”ON”.
3. Slide the closure strip into the closure track until
the strip stops (refer to Part B, LOADING A
ROLL OF CLOSURES in this section).
4. Press the run switch to ”RUN”. A closure will
move into the closing position, if one is not
already there, and the ”READY” light goes on
indicating the closer is ready for use.
5. Close the bag and remove it from the closer
(refer to Part E, CLOSING BAGS in this
section).
6. The closer cycles, prints a closure (If a printer
Model) and positions a new closure into the
closing position, ready for the next bag. The
”READY” light will go off momentarily as the clo-
sure is loading.
7. If no closure is available to move into the
closing position, the machine will continously
cycle and the ”READY” light will flash on and off
repeatedly until the run switch is pressed to
”STOP”. Closures can now be loaded into the
machine.
Figure 2.1
Power switch
Ready light
Run switch
086B 02 18
Summary of Contents for 086B-100
