SECTION IV
Troubleshooting
P 4.2
4. The closer cycles and the
”READY” light blinks
repeatedly. There is no
closure between the check
and pick.
5. The closer cycles and the
”READY” light blinks
repeatedly. There is a
closure between the check
and pick that does not
advance.
6. The closer continues to
cycle while the switch is in
the “STOP” position. The
”READY” light does not
blink.
7. The closer cycles even
though a closure is in the
bag-closing position. One
or more closures are
pushed out the front of the
closure track.
A. The closer is operating
properly.
A. The wrong closures are
being used.
B. The check is not adjusted
properly.
C. The pick does not advance
the closure.
A. The cam switch is not
functioning properly.
A. The sensor lever is not
detecting the closure.
Move the switch to the “STOP” position. Refer
to Section II Operation, Part B. LOADING A
ROLL OF CLOSURES.
The 086 is available in six models. Refer to
Section I Specifications to determine the correct
closure for your model closer.
Refer to Section III, Adjustments, Part C.RE-
MOVE THE FRONT SHIELD, and Part D.
CHECK POSITION.
Refer to Section III, Adjustments, Part C.RE-
MOVE THE FRONT SHIELD, and Part D.
CHECK POSITION. Look under the front of the
closure track to see if the tips of the pick are lo-
cated in the slots at the bottom of the closure
track. If it is not, center the pick by hand. The
pick is held up by the pick spring located at the
back of the pick assembly. The pick should
move down when a light force is applied to it.
When released, the pick should move back up
due to the spring tension. Some side play is
normal when the pick is out of the closure track
slots.
The cam switch stops the motor in the proper
position and turns on the ”READY” light. See
Section III, Adjustments, Part N. CAM SWITCH
MOUNTING and SECTION VI, Wiring Diagram.
The lever of the cam switch may be bent, the
cam switch may be defective, or the switch cam
may not be mounted properly. Correct as
needed.
See Section III, Adjustments, Part G. SENSOR
LEVER SPRING, Part H. SENSOR LEVER
STOP ADJUSTMENT, and Part I. LOK SEN-
SOR SWITCH ADJUSTMENT.
PROBLEM
SYMPTOM
CORRECTION
086B 02 18
Summary of Contents for 086B-100
