background image

5

3BA00221 • 2014-09-18 • Rev. 5 

ersa i-CON2 & i-CON 2V

Commissioning

 

Connect the soldering iron to the station 

. For this 

purpose, insert the male connector into the female 

connector and lock them shut. Place the soldering iron 
on the soldering stand.

 

Ensure that the male connector is inserted correctly 

into the female connector. The pin ② in the male 
connector must match up with the groove ③ on the 

female connector.

 

Connect the power supply cable to the soldering sta-

tion and power outlet.

 

Turn the soldering station on.

Attention!

 Danger of burns! The soldering iron tips heat up  immediately 

after the device is switched on!

2.3 

Connect compression unit C100

Compression unit C100 is only requested during unsoldering tool opera-

tion.

 

Place the soldering station and compression unit 
switch on "0".

 

Insert the compression unit plug.

 

Firmly attach pre-filter 

 to the vacuum connection 

(VAC) on the compression unit.

 

Attach the X-TOOL/X-TOOL VARIO vacuum connection 

 to the pre-filter.

 

Connect the tool to the soldering station connector.

 

Use the switch to turn on the compression unit and the 
soldering station.

 

Summary of Contents for Ersa i-CON 2













Reviews: