Kuppersbusch KD 6210.0 GE, Instructions For Use And Installation

Page: 18 / 32

18
ENG
1 150/ 120 mm reduction.
1 Anti-recoil valve.
2 Support for tubecover.
4 Wall plugs (Ø6 x 30).
4 Wall plugs (Ø8 x 40).
4 Long bolts (Ø4 x 30).
2 Screws (Ø3,9 x 19).
6 Long bolts (Ø5 x 45).
2 Ø6,4 x Ø18, washers.
2 Clips.
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
14 are complied with.
To obtain optimum performance, the external
conduct must not be more than FOUR
METRES long, have no more than two 90°
angles and its diameter must be at least Ø120.
1) Trace and drill the points for fitting the wall plugs
onto the wall (A1) (Ø8 x 40). See figure nr. 1.
2) Fit the wall plugs (A1) and screw in the long bolts
(A2) (Ø5 x 45) leaving them protruding 5 mm out of
the wall.
3) Attach the kitchen hood to the long bolts (A2).
Straighten the apparatus and tighten the long bolts.
4) Remove the metal filters. Loosen the screws
(without unscrewing them) of the EASYCLEAN
panels (A19), move the panels aside carefully and
take them off.
5) Trace the location of the wall plugs (R) (Ø8 x 40),
through the inside of the kitchen hood.
6) Loosen the long bolts (A2) and take the kitchen
hood off.
7) Drill into the wall and fit the wall plugs (R).
8) Attach the kitchen hood, tighten the long bolts (A2)
and (S) (Ø5 x 45) with the washers (T) (Ø6,4 x Ø18).
9) Mount the EASYCLEAN panel again (A19). Fit the
metal filters.
10) Mount the tubecovers, attaching the lower one to
the support (H) as per the detail in figure 1. Lift the
upper tubecover up to the desired height and mark
its shape on the wall. Remove the tubecovers.
11) Fit the clips (F) to the support (C).
12) Centre the support (C) around the shape
marked; trace and drill the fixing points for the wall
plugs (E) (Ø6 x 30). Attach the support (C) with the
long bolts (D) (Ø4 x 30).
13) Fit the part (A) if the inner tubecover (not
supplied) is Ø150 or (A) + (B) if it is Ø120.
14) Attach the inner tube with a clamp (not supplied)
to (B) or on to the motor's air outlet vent as the case
may be.
15) Once the inner tube is fitted, fit the lower
tubecover around the extractor fan outlet and attach
the upper tubecover with the screws (G) (Ø3,9 x 19).
When exterior gas extraction is not possible, then the
kitchen hood may be set to purify the air by recycling
it through active charcoal filters.
The active charcoal filters have an active life of
between three to six months, depending on the
individual conditions of use. These filters cannot be
washed nor regenerated. They must be replaced
once their useful life comes to an end.
Fig. 2 (Page 19)
1) Remove the metal filters. Loosen the screws
(without unscrewing them) of the EASYCLEAN
panels (K), move the panels aside carefully and take
them off.
2) Put the filters into the lateral draught section of the
motor making the holes in the filters match up (A)
with the pivots (B) of the motor carcass. Turn as
indicated in the diagram.
3) Mount the EASYCLEAN panel again (K). Fit the
metal filters.
4) Remove the tubecovers (E). Fit the diffuser (C) on
to the motor's air outlet vent. Fit the tubecovers back
on (E).
Active charcoal filters (Optional)
Installation
Accesories supplied