KUHN Venta 3030 Operator'S Manual Download Page 55

Page: 55 / 136

7. - Putting into service

Venta 3030-3530-4030

RN034AGB D

Seed Drill

7.4.2 Description of coupling elements

The machine is equipped with:

• A 7-pin electric plug for the electrical signalling

equipment.

• An electric 9-pin plug to supply the ISOBUS

module
or

•

An electric 3-pin plug to supply the

QUANTRON S-2 module

• Hydraulic hoses for the blower drive (depending

upon specification).

• 2 hydraulic hoses for the third hydraulic point

(depending upon specification)

•

One hydraulic hose for the pre-emergence

markers (depending upon specification).

• Two 3 pin plugs for the markers (depending upon

specification).

• A 5 pin plug for the hydraulic valve (depending

upon specification).

• A 3 pin plug for the work position sensor

7.4.3 Blower unit drive

The VENTA 1030 seed drill is factory fitted with a
hydraulic blower drive.

2300 min

-1

4300 min

4200

-1

max

Summary of Contents for Venta 3030









































































































































Search results

Summary of Contents for Venta 3030

Reviews:

Related manuals for Venta 3030

Brands by name

Popular brands

KUHN Venta 3030, Operator'S Manual

Search results

Summary of Contents for Venta 3030

Reviews:

Related manuals for Venta 3030

Brands by name

Popular brands