KUHN Venta 3030 Operator'S Manual Download Page 22 | Manualshive

Page: 22 / 136

background image

Venta 3030-3530-4030

20

4. - Safety

RN034AGB D

Seed Drill

4.2.8 Precautions when coupling

Before attaching the machine, make sure that it
cannot accidentally start moving (chock the wheels)
and that the parking stand is in the right position.

The machine must only be attached to the hitch
points provided for this purpose.

Never stand between the tractor and the machine
when operating the three point linkage.

Do not stand between the machine and the tractor
or on the machine without having first applied the
tractor parking brake and placed the gearbox in the
neutral position.

«
...
20
21
22
23
24
...
»

Summary of Contents for Venta 3030









































































































































Reviews:

No comments

Related manuals for Venta 3030

Brand: Labnet Pages: 2

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: Xo Pages: 59

Brand: Falcon Pages: 8

Brand: Garelick Pages: 4

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Palmer Pages: 2

Brand: Pari Pages: 282

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brand: YASKAWA Pages: 81

Brand: YASKAWA Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands