KUHN Venta 3030 Operator'S Manual Download Page 26

Page: 26 / 136

Venta 3030-3530-4030

4. - Safety

RN034AGB D

Seed Drill

4.2.16 Precautions for machine use

After each use, check the tools (blades) and their
attachment hardware in accordance with the
instructions given in the present manual.

Check the guards regularly. Immediately replace
any damaged or missing elements.

Make sure all the guards are in place. Keep all
persons and animals away from the danger zone.
Check that nobody is within the side marker
operating area on headlands.

Stay a safe distance from the machine when the
cutting tools are in movement.

Never work in reverse.

4.2.17 Precautions to take before using the

parking stands

134138: Specific requirements for countries member of the Eurasian Economic Community (EAC marking).

134139: Specific requirements for countries member of the Eurasian Economic Community (EAC marking).

133983: Specific requirements for countries member of the Eurasian Economic Community (EAC marking).

133987: Specific requirements for countries member of the Eurasian Economic Community (EAC marking).

133988: Specific requirements for countries member of the Eurasian Economic Community (EAC marking).

Summary of Contents for Venta 3030









































































































































Search results

Summary of Contents for Venta 3030

Reviews:

Related manuals for Venta 3030

Brands by name

Popular brands

KUHN Venta 3030, Operator'S Manual

Search results

Summary of Contents for Venta 3030

Reviews:

Related manuals for Venta 3030

Brands by name

Popular brands