KUHN ATHENOR 6070 Operator'S Manual Download Page 81

Page: 81 / 98

Maintenance and storage

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

4. Cleaning the conveyor

The conveyor is contained in a unit to keep it clean.

Open the emptying hatch once a week to remove

product accumulated at the back of the unit.

How to proceed:

• Set the tractor distribution lever to the continuous

pumping position.

• Engage the tractor PTO and the beater bar.
• Put the conveyor into forward for a few seconds to

bring out any product accumulated at the back of the
unit.

• Stop the conveyor; disengage the beater bar then

the tractor PTO.

• Stop the tractor engine and remove ignition key.

• Pull on the locking handles (1).
• Release the hooks holding the ring (2).
• Open the hatch as wide as possible (3).
• Use a broom or similar to remove any product left

inside.

• Raise the hatch and put the two hooks into the rings

before lifting the handles.

• Lock the hatch by lifting the handles.

Wait for a few moments until the machine has
completely stopped.

Summary of Contents for ATHENOR 6070



































































































Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands

KUHN ATHENOR 6070, Operator'S Manual

Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands