KUHN ATHENOR 6070 Operator'S Manual Download Page 69

Page: 69 / 98

Optional equipment

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Optional equipment

1. Hydraulic unit

Kit no.: 1926193

The hydraulic unit is designed to provide the hydraulic

power needed to run the machine.

It is suitable for use with tractors of low hydraulic power,

while guaranteeing optimal operation of its functions.

Description

- Auxiliary hydraulic unit
- Driven by the tractor power take-off
- Pump 55 cm

, speed at a power take-off rate of 540

min

-1

: 45 l/min

- 60 litre tank with filter and level
- Circuit protected by valve calibrated to 190 bar
- Recommended oil: type ISO VG 46 (HV), for example:

SHELL HYDRAU PW

Functioning

- Before starting the machine, check the oil level in the

tank.

- Connect the tractor power take-off transmission and

the pump step-up gearbox drive shaft, then lock.

- The machine must be driven at a rated power-take-off

rate of 540 min

-1

The hydraulic unit can be mounted on machines
already in service.

A slight gear noise may be heard at low
speed. Use the hydraulic unit at a minimum
power take-off rate of 300 min

-1

Summary of Contents for ATHENOR 6070



































































































Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands

KUHN ATHENOR 6070, Operator'S Manual

Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands