KUHN ATHENOR 6070 Operator'S Manual Download Page 56

Page: 56 / 98

Silo unloader - Straw spreader - Mixer - Distributor

ATHENOR 6070

Instructions for work

5. Silage unloading

Approaching the silo

- Set the hydraulic distributo control to continuous

pumping mode.

- Raise the arm and the hook as far as possible to

ensure good visibility and avoid crushing the heap
following a collision.

- Lower the machine as far as it will go, taking care to

avoid scraping the heel along the ground, then
reverse towards the front of the silo.

- Set the heel of the machine on the ground before

contacting the silage to be unloaded.

For a corridor silo, position the machine slightly on the

bias so as to load as close to the wall as possible.

For a machine equipped with a hydraulic unit,
you must set the gearbox to neutral..

Never attempt to penetrate the silo by
reversing forcefully.

Summary of Contents for ATHENOR 6070



































































































Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands

KUHN ATHENOR 6070, Operator'S Manual

Search results

Summary of Contents for ATHENOR 6070

Reviews:

Related manuals for ATHENOR 6070

Brands by name

Popular brands