manualshive.com logo in svg

Kubota VS 220, User Manual

Share
Download
Kubota VS 220 User Manual Download Page 86

To be done before spreading

86

Fine application

All  three  dosing  openings  normally  open  uniformly  with  the  dosing 

setting you set. With a low application rate and/or a low driving speed 

the  dosing  openings  are  only  opened  a  slight  bit  so  that  very  little 

fertiliser would stream through the dosing openings of the spreader. 

This  could  easily  cause  blockage,  which  would  lead  to  a  bad 

spreading pattern and possible damage the crops.

We therefore advise that you make use of the fine application kit if the 

flowrate is 

less than 45 lbs/min

.

Close 2 of the 3 dosing openings to prevent blockages. The remaining 

opening  will  be  further  opened  as  the  flowrate  with  the  constant 

flowrate would be three times as much.

In order to close 2 of the 3 dosing openings, the fine application kit is 

fitted in place of the agitator.

Adjusting dosing for fine 

application via the website

When  you  apply  the  fine  application  kit  you  must  use  the  dosing 

setting of a 3 times higher flowrate.

Adjust the dosing with

•

the online spreading chart

Here you have the option of fine/ non-fine application.

The chart below indicates under the heading “settings” that fine 

application is applied. The shown dosing setting has then already 

been converted.

Install the fine application kit.

See paragraph »Fitting the fine application kit« on page 88.

Agitator

Dosing openings

Locking bolts

Basic application l 40 feet l 100 lbs/acre l 5mph - Granular

Note!

The flow rate will be very low! We advise you to use the fine application kit. Do you wish to use this fine 

application kit?

Flowrate

Regulating rod position

Summary of Contents for VS 220



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands