manualshive.com logo in svg

Kubota VS 220, User Manual

Share
Download
Kubota VS 220 User Manual Download Page 103

To be done before spreading

103

Testing full-field spreading 

pattern with border 

spreading

Connecting spreading pattern 

with border-spreading plate

Then test the connecting full-field spreading pattern with the right 

PTO shaft rpm.

Divide the troughs as described below; with a fictitious ditch.

Review and adaptation

The  maximum  acceptable  loss  in  the  ditch  is  determined  by 

environment  standards  (EN  13739-1).  In  order  to  comply  with  the 

standards,  the  quantity  of  fertiliser  in  the  trough,  standing  in  the 

fictitious ditch, must be a maximum of 10% of the quantity collected in 

the trough in the middle of the track (= 100%).

Adjust the PTO shaft rpm at the first full-field round if more than 

10% is spread into the ditch.

I

NDICATION

Bring the PTO shaft rpm for the successive rounds back to the 

correct value.

Connecting spreading pattern 

with border-spreading cylinder

Perform  the  first  round  with  the  border-spreading  cylinder  at  half 

working width from the field boundary or ditch.

Check if the furthest fertiliser granules get spread up to the tractor 

tracks of the next full pass.

Place the troughs lengthwise onto the driven tractor track on the 

side of the next round.

Spread the first full-field round and check a few granules lying in 

the troughs.

Possibly adjust the rpm slightly.

Keep the driving speed constant at the value with which you 

calculated the application rate!

I

NDICATION

If you are using the ED II the dosing will automatically be adjusted to 

the new driving speed.

Fictitious ditch

 X m

Furthest fertiliser granules up to next track?

Placing troughs

Ditch side

1/2 X

X

Summary of Contents for VS 220



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands