manualshive.com logo in svg

Kubota VS 220, User Manual

Share
Download
Kubota VS 220 User Manual Download Page 28

Getting familiar with the machine

28

Spreading pattern

The quality of the spread fertiliser and a well-set machine are essential 

for a good spreading pattern.

The spreading pattern is also determined by:

•

the working width,

•

the type of spreading spout,

•

the set angle of the turn of the spreading spout

•

the PTO shaft rpm,

•

the use of the border-spreading plate or the border-spreading 

cylinder.

Depending on the above, a working width of 3 - 49 feet is possible.

Full overlap

The spreading pattern is a triangle with full overlap with all working 

widths up to 45 feet.

PTO shaft RPM

With working widths up to 40 feet, the PTO shaft rpm is as a rule 540 

rpm.

Larger working widths (40-49 feet)

A higher rpm is recommended for larger working widths.

N

OTE

Set only 620 rpm where the spreading chart indicates this!

Summary of Contents for VS 220



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands