manualshive.com logo in svg

Kubota AP-SBL2566, Operator'S Manual

Share
Download
Kubota AP-SBL2566 Operator'S Manual Download Page 3

Table of Contents

7/31/17

AP-SBL2566, AP-SBL2574, & AP-SBL2584 Snow Blowers 370-478MK

© 

Copyright 2017 All rights Reserved

Kubota provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Kubota
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Kubota reserves the right
to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. 

Kubota is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Table of Contents

Important Safety Information   . . . . . . . . . . . . .  1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 6
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Serial Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Section 1: Assembly & Set-up   . . . . . . . . . . . .  7

Skid Steer/Tractor Requirements   . . . . . . . . . . . . . . 7
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 7

Loading & Unloading  . . . . . . . . . . . . . . . . . . . . . . 7

Optional Outer Skid Shoes  . . . . . . . . . . . . . . . . . . . 7
Optional Inner Skid Shoes   . . . . . . . . . . . . . . . . . . . 7
SBL2566 Chute Assembly   . . . . . . . . . . . . . . . . . . . 8
SBL2574 & SBL2584 Chute Assembly  . . . . . . . . . . 8
Spout Deflector, Hydraulic Cylinder   . . . . . . . . . . . . 9
Quick Coupler Set-up  . . . . . . . . . . . . . . . . . . . . . . 10

Section 2: Equipment Hook-up & Unhook  . .  11

Snow Blower Hook-up . . . . . . . . . . . . . . . . . . . . . . 11
Hydraulic Hose Hook-up  . . . . . . . . . . . . . . . . . . . . 12
Solenoid Hook-up  . . . . . . . . . . . . . . . . . . . . . . . . . 12
Check Equipment Clearances  . . . . . . . . . . . . . . . . 13
Unhooking The Snow Blower   . . . . . . . . . . . . . . . . 14

Section 3: Options  . . . . . . . . . . . . . . . . . . . . .  15

Motor Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Flat Face Couplers  . . . . . . . . . . . . . . . . . . . . . . . . 15
Case Drain Coupler & Cable Ties  . . . . . . . . . . . . . 15
Electrical Control Harness (Optional)   . . . . . . . . . . 16

Control Harness With Deutsch 14 Pin Plug  . . . . 16
Control Harness With Deutsch 2 Pin Plug  . . . . . 17

Assembly Instructions  . . . . . . . . . . . . . . . . . . . . . . 18
Initial Preparations   . . . . . . . . . . . . . . . . . . . . . . . . 18
Mount Control Box (#2) in Cab  . . . . . . . . . . . . . . . 18
Connect to Power  . . . . . . . . . . . . . . . . . . . . . . . . . 18
Route Wire Harness (#3)   . . . . . . . . . . . . . . . . . . . 18
Hook-up Solenoid Harness (#4)   . . . . . . . . . . . . . . 19
Outer Skid Shoes   . . . . . . . . . . . . . . . . . . . . . . . . . 20
Inner Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Section 4: Adjustments   . . . . . . . . . . . . . . . . . 21

Discharge Chute & Spout Deflector . . . . . . . . . . . . 21

Spout Deflector Adjustment  . . . . . . . . . . . . . . . . 21
Chute Rotation Gear Alignment  . . . . . . . . . . . . . 21
Chute Rotation Adjustment   . . . . . . . . . . . . . . . . 21

Outer Skid Shoe Adjustment  . . . . . . . . . . . . . . . . . 22
Inner Skid Shoe Adjustment   . . . . . . . . . . . . . . . . . 22
Auger Speed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Level Run Indicator Adjustment . . . . . . . . . . . . . . . 23

Section 5: Operating Instructions  . . . . . . . . . 24

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
General Safety Information  . . . . . . . . . . . . . . . . . . 24
Mount & Dismount Skid Steer  . . . . . . . . . . . . . . . . 26
Inspection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating Safety Check   . . . . . . . . . . . . . . . . . . . . 27
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Leveling The Snow Blower   . . . . . . . . . . . . . . . . . . 28
General Operator Instructions  . . . . . . . . . . . . . . . . 28

Section 6: Maintenance & Lubrication   . . . . . 30

General Maintenance Information  . . . . . . . . . . . . . 30
Tractor/Skid Steer Maintenance   . . . . . . . . . . . . . . 30
Auger & Impeller Inspection   . . . . . . . . . . . . . . . . . 30
Outer Skid Shoe Option   . . . . . . . . . . . . . . . . . . . . 31
Inner Skid Shoe Option  . . . . . . . . . . . . . . . . . . . . . 31
Grader Blade  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 32
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Section 7: Specifications & Capacities  . . . . . 34
Section 8: Features & Benefits   . . . . . . . . . . . 35
Section 9: Troubleshooting  . . . . . . . . . . . . . . 36
Section 10: Torque Values Chart . . . . . . . . . . 37
Section 11: Warranty & Legal Disclaimer  . . . 38

Summary of Contents for AP-SBL2566













































Reviews:

No comments

Brands by name

Popular brands

Load more brands