manualshive.com logo in svg

Kubota AP-SBL2566, Operator'S Manual

Share
Download
Kubota AP-SBL2566 Operator'S Manual Download Page 11

7

Section 1: Assembly & Set-up

10/07/16

AP-SBL2566, AP-SBL2574, & AP-SBL2584 Snow Blowers 370-478MK

Table of Contents

Section 1: Assembly & Set-up

Skid Steer/Tractor Requirements

The SBL2566, SBL2574, & SBL2584 Snow Blowers are 
designed to attach to skid steers. The SBL2566 can also 
be attach to a tractor loader with a 3-point mounted 
hydraulic reservoir system (HRS) mounted on the back. 
The skid steer and/or tractor/HRS must meet the 
following minimum requirements:

SAE Lift Capacity . . . . . . . . . . . . . . . . . . . . .  1200 lbs
Hitch Type  . . . . . . . . . . . . . . .  Skid steer/loader plate
Hydraulic Pressure Rating  . . . . . . . . . 2500 - 3500 psi
Low Volume Motors & Hoses . . . . . . . . . .12 - 19 gpm
Medium Volume Motor & Hoses . . . . . . .  20 - 26 gpm
High Volume Motor & Hoses. . . . . . . . . .  27 - 33 gpm
Hydraulic Hoses . . . . . . . . . . . . .  2 - Hydraulic outlets
Case Drain Hose  . . . . . . . . . . . . .  1 - Hydraulic outlet

Skid Steer Weight . . . . . . . . . . . . . See warning below

!

WARNING

To prevent serious injury or death:  

Light weight power machines may need weights added to the 
rear to maintain steering control and prevent tipping. Consult 
your power machine Operator’s Manual to determine proper 
weight requirements and maximum weight limitations.

Torque Requirements

Refer to 

“Torque Values Chart”

 on page 37 to 

determine correct torque values for common bolts.

Loading & Unloading

Refer to Figure 1-1:

There are two lifting holes (one on each end panel). Use 
these holes to attach lift chains during loading/unloading 
and while installing skid shoes in assembly & set-up.

Lift Points

Figure 1-1

IMPORTANT:  

The skid steer or tractor mounted 

hydraulic reservoir system must be equipped with a 
case drain system.

37872

Outer Skid Shoe Assembly (Right-Hand Shown)

Figure 1-2

Optional Outer Skid Shoes

Refer to Figure 1-2:

1.

Attach outer right-hand skid shoe (#1) to the right-
hand side panel with 1/2"-13 x 1 1/4" GR5 carriage 
bolts (#2) and hex flange lock nuts (#3) using the 
bottom square holes as shown.

2.

Tighten hex flange lock nuts (#3) to the correct 
torque.

3.

Repeat steps 1 & 2 for the left-hand side.

Inner Skid Shoe Assembly (Left-Hand Shown)

Figure 1-3

Optional Inner Skid Shoes

Refer to Figure 1-3:

1.

Attach skid shoe mount (#2) to the back, left side of 
the Snow Blower with 1/2"-13 x 1 1/2" GR5 bolts (#3) 
and hex flange lock nuts (#4). Tighten hex flange lock 
nuts to the correct torque.

2.

Attach inner skid shoe (#1) to skid shoe mount (#2) 
with bent pin (#6) as shown. Secure bent pin with 
hairpin cotter (#5). 

3.

Repeat steps 1 & 2 for the back, right side of the 
Snow Blower.

37225

37226

Summary of Contents for AP-SBL2566













































Reviews:

No comments

Brands by name

Popular brands

Load more brands