manualshive.com logo in svg

Kubota AP-SBL2566, Operator'S Manual

Share
Download
Kubota AP-SBL2566 Operator'S Manual Download Page 12

8

Section 1: Assembly & Set-up

AP-SBL2566, AP-SBL2574, & AP-SBL2584 Snow Blowers 370-478MK

10/07/16

Table of Contents

SBL2566 Chute Assembly

Refer to Figure 1-4:

1.

Remove hex nuts (#8), spring lock washers (#9), hex 
head bolts (#7), bearing strap (#2A), and chute 
bearings (#4). Keep hardware for reuse.

2.

With discharge chute (#1) facing straight forward. 
Slide base of chute over UHMW chute bearing 
ring (#10) until base of chute is fully under chute 
rotational stop (#5), bearing strap (#2B), and 
engaged with sprocket (#3).

3.

Reattach bearing strap (#2A) to snow blower housing 
with existing 3/8"-16 x 1 1/2" GR5 bolts (#7), chute 
bearings (#4), lock washers (#9), and 
nuts (#8). Tighten nuts (#8) to the correct torque.

4.

Verify stop bolts (#6) are at the back as shown. 

SBL2574 & SBL2584 Chute Assembly

Refer to Figure 1-5:

1.

Remove hex nuts (#10), spring lock washers (#12), 
hex head bolts (#7), and rotational stop (#6). Keep 
hardware for reuse.

2.

Remove hex nuts (#11), spring lock washers (#13), 
hex head bolts (#9), bearing strap (#2A), and chute 
bearings (#5). Keep hardware for reuse.

3.

With discharge chute (#1) facing straight forward as 
shown. Slide base of chute over UHMW chute 
bearing ring (#14) until base of chute is fully under 
remaining bearing straps (#2B & #2C) and engaged 
with sprocket (#4).

4.

Reattach bearing strap (#2A) to snow blower housing 
with existing 3/8"-16 x 1 1/2" GR5 bolts (#9), chute 
bearings (#5), lock washers (#13), and nuts (#11). 
Tighten nuts (#11) to the correct torque.

5.

Reattach rotational stop (#6) to Snow Blower housing 
with existing 1/4"-20 x 3/4" GR5 bolts (#7), rotational 
stop (#6), lock washers (#12) and hex nuts (#10). 
Tighten nuts (#10) to the correct torque.

Refer to Figure 1-6:

6.

Verify stop bolts (#8A & #8B) are left of rotational stop 
(#6) as shown. 

7.

Tighten hex bolts (#7) to the correct torque.

IMPORTANT:  

Position chute (#1) facing straight 

forward to the front as shown in Figure 1-4 before 
sliding base of chute over bearing ring (#10).

IMPORTANT:  

Position chute (#1) facing straight 

forward to the front as shown in Figure 1-5 before 
sliding base of chute over bearing ring (#14).

SBL2566 Chute Assembly

Figure 1-4

SBL2574 & SBL2584 Chute Assembly

Figure 1-5

SBL2574 & SBL2584 Rotational Stop Bar Set-up

Figure 1-6

37432

35600

35601

Summary of Contents for AP-SBL2566













































Reviews:

No comments

Brands by name

Popular brands

Load more brands