manualshive.com logo in svg

Kubota AP-SBL2566, Operator'S Manual

Share
Download
Kubota AP-SBL2566 Operator'S Manual Download Page 23

19

Section 3: Options

10/07/16

AP-SBL2566, AP-SBL2574, & AP-SBL2584 Snow Blowers 370-478MK

Table of Contents

Attach Cable to Hydraulic Coupling Lines

Figure 3-11

Attach Solenoid Harness to Skid Steer Harness

Figure 3-12

Hook-up Solenoid Harness (#4)

Refer to Figure 3-5 on page 17 & Figure 3-12:

1.

If not already connected, connect attachment’s 
hydraulic hoses to the quick release couplings on the 
loader arm. Refer to 

“Hydraulic Hose Hook-up”

 in 

the attachment Operator’s Manual for detailed 
instructions.

2.

Connect 8'-11” long solenoid harness (#4) to wire 
harness (#3).

3

5

35229

4

3

Green wire 
Connector

Red wire 
Connector

Brown wire 
Connector

White wire 
Connector

35242

3.

Zip tie wire harness (#3) along one of he hydraulic 
hoses to the attachment’s solenoid. 

4.

Coil excess solenoid harness (#4) up and zip tie coil 
to the attachment. Leave enough harness to reach 
the solenoids.

Solenoid Wires

Figure 3-13

Refer to Figure 3-13:

5.

Refer to 

“Solenoid Hook-up”

 instructions in the 

attachment Operator’s Manual and below:

a. Locate solenoid on the attachment that controls 

the motor on the Snow Blower for rotating the 
spout left and right. Attach brown wire connector 
and white wire connector to that solenoid.

b. Locate solenoid on the attachment that controls 

the cylinder on the Snow Blower for tilting the 
discharge chute up and down. Attach green wire 
connector and red wire connector to that solenoid.

c. Return to the skid steer and operate tilt switch and 

rotate switch to verify they are functioning as 
desired. 

d. If either of the switches operated the cylinder or 

motor in the opposite direction desired, turn off 
engine, raise seat bar if included, move skid steer 
controls until they lock, and remove switch key 
before dismounting to make changes to the 
solenoid connections.

e. If tilt cylinder operates in the opposite direction 

desired, switch green wire connector with red wire 
connector.

f. If the motor operates in the opposite direction 

desired, switch brown wire connector with white 
wire connector.

Solenoid For Tilt (Up/Down) Cylinder
Attach Green/Red Connectors To This Solenoid

Solenoid For Rotate (Left/Right) Cylinder/Motor
Attach Brown/White Connectors To This Solenoid

35242

Summary of Contents for AP-SBL2566













































Reviews:

No comments

Brands by name

Popular brands

Load more brands