KTM BUI215 Operating Instructions Manual Download

Page: 72 / 74

Eng

lish – Pa

ge 7
0

uts

ch – S
eit

e 68

English –

proximately 20 % of the charging capacity. The flashing LED

indicates the next 20 % currently charging.
Once the eBike battery is fully charged, the LEDs go out im-

mediately and the on-board computer is switched off. The

charging process is terminated. The state of charge can be

displayed for three seconds by pressing the on/off but-

ton

(10)

on the eBike battery.

Disconnect the charger from the mains and the battery from

the charger.

When the battery is disconnected from the charger, the bat-

tery is automatically switched off.

Note:

If you have charged the battery on the bike, carefully

close the charging socket

(6)

with the cover

(7)

after char-

ging, so that no dirt or water can get in.
If the charger is not disconnected from the battery after

charging, after a few hours the charger will switch itself back

on, check the state of charge of the battery and begin the

charging procedure again if necessary.

Errors – causes and corrective measures

Cause

Corrective measures

Battery defective

Two LEDs flash on the battery.

Contact an authorised bike dealership.

Battery too warm or too cold

Three LEDs flash on the battery.

Disconnect the battery from the charger until the charging

temperature range has been reached.
Do not reconnect the battery to the charger until it has

reached the correct charging temperature.

The charger is not charging.

No LEDs flashing (one or more LEDs will remain perman-

ently lit depending on the state of charge of the eBike bat-

tery).

Contact an authorised bike dealership.

Charging not possible (no indicator on battery)

Connector not attached properly

Check all connections.

Battery contacts dirty

Carefully clean the battery contacts.

Plug socket, cable or charger defective

Check the mains voltage, have the charger checked over by a

bike dealership.

Battery defective

Contact an authorised bike dealership.

Maintenance and servicing

Maintenance and cleaning

If the charger fails, please contact an authorised bike dealer-

ship.

After-sales service and advice on using products

If you have any questions about the charger, contact an au-

thorised bike dealership.
For contact details of authorised bike dealerships, please

visit www.bosch-ebike.com.

Disposal

Chargers, accessories and packaging should be recycled in

an environmentally friendly manner.
Do not dispose of chargers along with household waste.

Only for EU countries:

According to the European Directive 2012/19/

EU on Waste Electrical and Electronic Equip-

ment and its implementation into national law,

chargers that are no longer usable must be col-

lected separately and disposed of in an envir-

onmentally friendly manner.

Subject to change without notice.

Bosch eBike Systems

0 275 007 XCX | (13.03.2020)

Summary of Contents for BUI215











































































Search results

Summary of Contents for BUI215

Reviews:

Related manuals for BUI215

Brands by name

Popular brands

KTM BUI215, Operating Instructions Manual

Search results

Summary of Contents for BUI215

Reviews:

Related manuals for BUI215

Brands by name

Popular brands