background image

01/FORK, TRIPLE CLAMP

23

200685-10

Measure the run-out of the inner tube.

Inner tub run-out

0.20 mm (

0.0079 in)

» If the measured value is greater than the specified value:

Change the inner tube.

200632-10

Check the outer tube for damage.
» If there is damage:

Change the outer tube.

200665-10

Check the surface of the sliding bushing.
» If the bronze-colored layer

A

under the sliding layer

B

is visible:

Replace the sliding bushing.

200666-10

Check the spring length.
Guideline

Spring length with preload spacer(s)

Weight of rider: 65… 75 kg (143…
165 lb.)

513 mm (20.2 in)

Weight of rider: 75… 85 kg (165…
187 lb.)

513 mm (20.2 in)

Weight of rider: 85… 95 kg (187…
209 lb.)

513 mm (20.2 in)

» If the measured value is greater than the specified value:

Reduce the thickness of the preload spacer.

» If the measured value is less than the specified value:

Increase the thickness of the preload spacer.

5.17

Assembling the compression damping fitting

Info

The steps are identical for both fork legs.

200704-11

Clamp the compression damping fitting in a bench vise using soft jaws.

Mount O-ring

1

and seal ring

2

.

Grease the O-ring.

Lubricant (T158) (

p. 270)

Summary of Contents for 350 EXC-F AUS 2012





































































































































































































































































































Reviews: