manualshive.com logo in svg

KSB MK, Installation & Operating Manual

Share
Download
KSB MK Installation & Operating Manual Download Page 34

7 Servicing/Maintenance

34 of 64

MK

 WARNING

Insufficient stability

Risk of crushing hands and feet!

▷

During assembly/dismantling, secure the pump (set)/pump parts to prevent
tilting or tipping over.

A regular maintenance schedule will help avoid expensive repairs and contribute to
trouble-free, reliable operation of the pump, pump set and pump parts with a
minimum of servicing/maintenance expenditure and work.

NOTE

All maintenance work, service work and installation work can be carried out by KSB
Service or authorised workshops. For contact details please refer to the enclosed
"Addresses" booklet or visit "

www.ksb.com/contact

" on the Internet.

Never use force when dismantling and reassembling the pump set. 

7.2 Servicing/Inspection

7.2.1 Supervision of operation

 DANGER

Impermissibly high temperatures

Explosion hazard!

Damage to the pump!

▷

Prolonged operation against a closed shut-off element is not permitted
(heating up of the fluid).

▷

Observe the temperature limits in the data sheet and in the section on
operating limits. (

ð

 Section 6.2, Page 29)

 DANGER

Excessive temperatures as a result of bearings running hot or defective bearing
seals

Explosion hazard!

Fire hazard!

Damage to the pump set!

Risk of burns!

▷

Regularly check the lubricant level.

▷

Regularly check the rolling element bearings for running noises.

CAUTION

Fluid level below the specified minimum

Damage to the pump set by cavitation! Dry running of the plain bearings!

▷

Never allow the fluid level to drop below the specified minimum.

While the pump is in operation, observe and check the following:

▪

The pump must run quietly and free from vibrations at all times.

▪

Check the shaft seal.

▪

Check the static sealing elements for leakage.

Summary of Contents for MK

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands