manualshive.com logo in svg

KSB MK, Installation & Operating Manual

Share
Download
KSB MK Installation & Operating Manual Download Page 26

5 Installation at Site

26 of 64

MK

CAUTION

Pump set running dry

Increased vibrations!

Damage to mechanical seals and bearings!

▷

Never operate the pump set for more than 60 seconds outside the fluid to be
handled.

CAUTION

Drive and pump running in the wrong direction of rotation

Damage to the pump!

▷

Refer to the arrow indicating the direction of rotation on the pump.

▷

Check the direction of rotation. If required, check the electrical connection and
correct the direction of rotation.

The correct direction of rotation of the motor and pump is clockwise (seen from the
drive end).

1. Start the motor and stop it again immediately to determine the motor's

direction of rotation.

2. Check the direction of rotation. 

The motor's direction of rotation must match the arrow indicating the direction
of rotation on the pump.

3. If the motor is running in the wrong direction of rotation, check the electrical

connection of the motor and the control system, if applicable.

Summary of Contents for MK

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands