KSB MK Installation & Operating Manual Download Page 25

Page: 25 / 64

5 Installation at Site

25 of 64

DANGER

Electrostatic charging

Explosion hazard!

Damage to the pump set!

▷

Connect the potential equalisation conductor to the earthing terminal
provided.

▷

Make sure that the connection between pump and baseplate is electrically
conductive.

▷

Screws, bolts, nuts and shims must not be coated or the coating must be
removed.

▷

Provide potential equalisation between the pump set and the foundation.

DANGER

Electrical connection work by unqualified personnel

Risk of fatal injury due to electric shock!

▷

Always have the electrical connections installed by a trained and qualified
electrician.

▷

Observe regulations IEC 60364 and, for explosion-proof models, EN 60079.

WARNING

Incorrect connection to the mains

Damage to the mains network, short circuit!

▷

Observe the technical specifications of the local energy supply companies.

NOTE

A motor protection device is recommended.

1. Check the available mains voltage against the data on the motor name plate.

2. Select an appropriate starting method.

5.8 Checking the direction of rotation

DANGER

Pump set running dry

Explosion hazard!

▷

Check the direction of rotation of explosion-proof pump sets outside
potentially explosive atmospheres.

WARNING

Hands inside the pump casing

Risk of injuries, damage to the pump!

▷

Always disconnect the pump set from the power supply and secure it against
unintentional start-up before inserting your hands or other objects into the
pump.

Summary of Contents for MK

































































Search results

Summary of Contents for MK

Reviews:

Brands by name

Popular brands

KSB MK, Installation & Operating Manual

Search results

Summary of Contents for MK

Reviews:

Brands by name

Popular brands