KSB Amacan K Installation & Operating Manual Download Page 95

Page: 95 / 126

9 Related Documents

95 of 126

Amacan K

1579.807/07-EN

9.2.7 Bearing bracket, sensors and terminals

69-14.01

900.06

932.06

81-2.01

81-29.01

81-2.03***

900.06***

932.06***

82-5.51**

914.51**

69-8.50**

82-5.50**

82-14.50**

550.50**

835

185.36

81-18.01

81-18.02

550.23

920.23

920.24

932.23

914.19

932.19***

99-4.01**

99-17.01

900.30

914.48

243

Fig. 63:

Bearing bracket, sensors and terminals

H: alignment groove

**: Only for version with measurement transmitter 69-8.50 (vibration sensor)

***: On specific sizes only

Table 49:

Symbols key

Symbol

Description

243

Always secure screwed connections marked with this symbol with

Loctite 243

Table 50:

List of components

Part No.

Description

Part No.

Description

185.36

Plate

82-14.50

Cable with plug

550.23/.50

Disc

835

Terminal board

69-8.50

Measurement transmitter

900.06/.30

Bolt/screw

69-14.01

Leakage monitor

914.19/.48/.51

Hexagon socket head cap screw

81-18.01/.02

Cable terminal

920.23/.24

Nut

81-2.01/.03

Plug

932.06/.19/.23

Circlip

81-29.01

Terminal

99-17.01

Desiccant

82-5.50/.51

Adapter

99-4.01

Conversion kit

Summary of Contents for Amacan K































































































































Search results

Summary of Contents for Amacan K

Reviews:

Related manuals for Amacan K

Brands by name

Popular brands

KSB Amacan K, Installation & Operating Manual

Search results

Summary of Contents for Amacan K

Reviews:

Related manuals for Amacan K

Brands by name

Popular brands