KSB Amacan K Installation & Operating Manual Download Page 74

Page: 74 / 126

7 Servicing/Maintenance

74 of 126

Amacan K

1579.807/07-EN

5. Fasten cable gland 834.02 with socket head cap screws 914.05 and secure the

screwed connection with Loctite 243.

6. Connect plug 81-2 to the control cable cores.

Fastening the cover plate to

the bail

The motor housing cover has been removed, placed down and protected against
rolling off.

The power cable has been fitted as described in this manual.

The control cable has been fitted as described in this manual.

1. Insert the power and control cables with cable protector 81-97 into cover plate

82-11 or 68-3.02.

2. Fasten the cover plate to the bail.

7.7.3 Fitting the motor housing cover

DANGER

Electrical connection work by unqualified personnel

Danger of death from electric shock!

▷

Always have the electrical connections installed by a trained and qualified
electrician.

▷

Observe the EN 61557 regulations as well as any regional regulations.

571

811

80-1

812

914.01

903.51

811

80-1

550.23

920.23

920.24

932.23

835

81-2

A - A

243

Fig. 41:

Fitting the motor housing cover

Alignment grooves of motor housing cover 812

Alignment groove of motor housing 811

Summary of Contents for Amacan K































































































































Search results

Summary of Contents for Amacan K

Reviews:

Related manuals for Amacan K

Brands by name

Popular brands

KSB Amacan K, Installation & Operating Manual

Search results

Summary of Contents for Amacan K

Reviews:

Related manuals for Amacan K

Brands by name

Popular brands