manualshive.com logo in svg

Krone EasyCut F 280, Original Operating Instructions, Page: 53 / 96

Share
Download
Krone EasyCut F 280 Original Operating Instructions Download Page 53

 

Settings

 

53 

 

Pos: 100.9 /Ü berschriften/Ü berschriften 2/A-E/EEinstellung der Entlastungsfeder n @ 0\mod_1196666659447_78.docx @ 10133 @ 2 @ 1 

 

10.2 

Adjusting the Compensation Springs  

Pos: 100.10 /BA/Sicher hei t/7. Gefahrenhinweise alt/Mähwer ke/Gefahr - Einstellung an den Entlastungsfeder n @ 0\mod_1196751594562_78.docx @ 12575 @  @ 1 

 

 

Danger! - Setting on the compensation springs 

Effect: Danger to life or serious injuries 
•  The compensation springs must only be removed in transport position. In the working 

position the compensation springs are subject to high tensile stress. 

•  Severe injury can be caused if the compensation springs are removed while in the working 

position. 

•  The lower threaded blocks on the compensation springs must be fully screwed in. 

 

Pos: 100.11 /BA/Ei nstellungen/Mähwer ke/EasyC ut/Bodendr uck/Bodendruck allgemei ner Text alle EC @ 0\mod_1196667271181_78.docx @ 10190 @  @ 1 

 

The ground pressure for the cutter bar is adjusted to local conditions by means of the 

compensation springs. In order to protect the sward the load on the mowing spar must be 

relieved so that it does not jump when mowing, yet does not leave any skid marks on the 

ground. 

Pos: 100.12 /BA/Ei nstellungen/Mähwer ke/EasyC ut/Bodendr uck/Bodendruck einstell en Bild EC  F280/320/360 @ 136\mod_1352883434463_78.docx @ 1211705 @  @ 1 

 

 

Fig. 28 

Pos: 100.13 /BA/Ei nstellungen/Mähwer ke/EasyC ut/Bodendr uck/Bodendruck einstell en Text EC 28/32 28/32C V @ 10\mod_1221737841223_78.docx @ 136908 @  @ 1 

 

 

Note 

Retaining chain shorter= reduced ground pressure 

Retaining chain longer= increased ground pressure 

 

If a telescope upper suspension arm is being used (optional)

The higher the compensation springs (1) are hooked into the perforated bar (2), the lower the 

pressure on the ground in the front part of the cutter bar.

If the compensation springs are hooked in too high, the mowing unit will tip towards the 

rear. 

or: 
The lower the compensation springs (1) are hooked into the perforated bar (2), the greater the 

pressure on the ground in the front part of the cutter bar.

If the compensation springs are hooked in too low, the mowing unit will have too much 

weight on the ground in front. 

 

Pos: 101 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Summary of Contents for EasyCut F 280

































































































Reviews:

No comments