Kramer VS-1616SDI User Manual Download Page 36

Page: 36 / 52

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Using the MENU Command Sequence

8.3.1 Understanding the SWITCHING METHOD Settings

Setting the

VS-1616SDI

unit as a Stand-Alone UNIT provides a choice of 4

SWITCHING METHOD settings:

NoVIS

- switching occurs immediately after completion of front

panel or dry-contact operation or immediately after receiving an

RS-232 or RS-485 command, or an IR command. The switching

is independent of the vertical reference

EXTERNAL SYNC ANALOG

- switching occurs during the

vertical interval of the video reference signal connected to the

ANALOG connector (this signal should be properly terminated
via the 75 (Term) button

)

EXTERNAL SYNC DIGITAL

- switching occurs during the

vertical interval of the video reference signal connected to the

DIGITAL connector

INT# 1

DIGITAL

- switching occurs during the vertical interval

of the video signal connected to Input # 1

Before choosing the

EXTERNAL SYNC DIGITAL

or the

INT# 1

DIGITAL

SWITCHING METHOD setting, it is necessary to install a

digital Genlock input board

. Without installing the optional digital Genlock

input board, these SWITCHING METHOD setting commands will be

unavailable.
Setting the

VS-1616SDI

unit as a Large Matrix (instead of as a Stand-Alone

UNIT) provides a choice of 5 SWITCHING METHOD settings:

NoVIS

EXTERNAL SYNC ANALOG

EXTERNAL SYNC

DIGITAL

INT# 1 DIGITAL

, (as described above)

MTX

(SYNC from Matrix) - the vertical interval of the video

reference (selected on one unit in the Large Matrix system) is

present on the “SYNC” RS-485 terminal block connector

. This

reference signal applies to all switchers in the multi- switcher

system and facilitates switching all

VS-1616SDI

units

simultaneously

To choose the MTX (SYNC from Matrix) setting

as the example in Figure

14 illustrates:

1 Item 4 in Figure 2
2 Available for purchase as an optional extra
3 Item 6 in Figure 2
4 This sets the matrix sync configuration from another (Master) machine

Summary of Contents for VS-1616SDI





















































Search results

Summary of Contents for VS-1616SDI

Reviews:

Related manuals for VS-1616SDI

Brands by name

Popular brands

Kramer VS-1616SDI, User Manual

Search results

Summary of Contents for VS-1616SDI

Reviews:

Related manuals for VS-1616SDI

Brands by name

Popular brands