manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 25

Operating Instructions

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

25

Operation at a glance

Operation of the basic functions

Operation at a glance

General operating steps

The following table describes the password entry as well as general operating steps, such as the chan-
ging of values and units. The password is included in the scope of delivery and consists of four digits.

Tab. 2 General operating steps

Aim

Operating steps

Entering the password
see "2.01 Enable password", page 30

1. Select Page 2.01.
2. Press SET.
3. Press the ARROW UPor ARROW DOWN key. The pass-

word prompt is displayed. The flashing cursor indicates 
the active input field.

4. Use the ARROW RIGHT / ARROW LEFT key to change 

the position within the number input.

5. Use the ARROW UP / ARROW DOWN key to increase 

or decrease keys. 

6. Repeat Steps 3 and 4 for all the numbers.
7. Press SET.

The password is deactivated. Entries are possible.

8. Repeat Steps 1–3 to activate the password.

Changing the value

1. Enter the password, see above.
2. Change to the desired page.
3. Press SET.

The flashing cursor indicates the active input field.

4. Use the ARROW RIGHT / ARROW LEFT key to change 

the position within the number input.

5. Use the ARROW UP / ARROW DOWN key to increase 

or decrease keys. 

6. Repeat Steps 3 and 4 for all the numbers.
7. Press SET.

The value is changed.

Changing the unit

1. Enter the password, see above.
2. Change to the desired page.
3. Press SET.

The active input field is marked.

4. Use the ARROW UP / ARROW DOWN keys to change 

the unit.

5. Press SET.

The unit is changed.

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands