manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 22

22

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

Operating Instructions

Connecting cables

Electrical connection

Connecting the sensors

Prerequisites:

□

The pick ups are mounted

Aids:

□

KRAL tool set

□

Diagonal cutter

1. Remove the rear device cover.

2. Adapt the cable gland to the cable diameter and cut it to length, see "Connecting cables to the ten-

sion spring terminals", page 21.

3. Pull the cables of the pick ups through the cable glands.

4. Connect the cables for the pick up of Volumeter A in accordance with the terminal diagram, see 

"Pick ups", page 19.

5. Replace the rear device cover.

Connecting analog and pulse outputs

Aids:

□

KRAL tool set

□

Diagonal cutter

1. Remove the rear device cover.

2. Adapt the cable gland to the cable diameter and cut it to length, see "Connecting cables to the ten-

sion spring terminals", page 21.

3. Pull the cables for the analog, and pulse outputs individually through the cable glands.

4. Connect the cables for the analog and pulse outputs in accordance with the terminal diagram, see 

"Connection assignments", page 19.

5. Lay the cables for the analog and pulse outputs to the consumer.

6. Connect the loads.

7. Replace the rear device cover.

Connecting the power supply

Prerequisites:

□

All the pick ups are connected

Aids:

□

KRAL tool set

□

Diagonal cutter

1. Remove the rear device cover.

2. Adapt the cable gland to the cable diameter and cut it to length, see "Connecting cables to the ten-

sion spring terminals", page 21.

3. Pull the power cable through the cable glands.

4. Connect the cable to the terminals.

5. Ensure that the system is disconnected.

6. Connect the power cable to the power supply of the system.

7. Replace the rear device cover.

The electronic unit is ready to operate.

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands