manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 11

Operating Instructions

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

11

Safety instructions on installation, removal and connection

Installation and removal

Installation and removal

Safety instructions on installation, removal and connection

Installation

Dimensions

Scope of delivery

The following components belong to the scope of delivery of the electronic unit:

□

Operating Instructions

□

Password

□

Worksheet

□

Mounting frame including screws and lock washers

□

Terminal tool

□

KRAL tool set

The following safety instructions must be observed:

□

All installation and removal work may only be carried out by qualified personnel.

▪

Read the operating instructions and observe the relevant instructions.

□

The electronic unit is a precision instrument.

▪

Ensure cleanliness and take care during installation and removal.

▪

Do not take apart the electronic unit.

□

The following qualifications are required for the electrical connection:

▪

Practical electrotechnical training

▪

Knowledge of the safety guidelines at the workplace

▪

Knowledge of the electrotechnical safety guidelines

Fig. 1

Dimensions of BEM 300 electronic unit

1

Height:

2

Width:

3

Depth:

116 mm
116 mm
116 mm

1

2

3

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands