manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 38

38

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

Operating Instructions

Accessories mounting

Accessories

Fixing kit OME

Adapter set for conversion of BEM 4U to BEM 300/500

1. Dismount the BEM 4U.
2. Slide the front frame 

2

 and the sheeting with seal 

3

 from behind onto the electronic unit 

1

.

3. Place the electronic unit in the control cabinet.
4. Slide on the sheeting 

5

 and the sealing frame 

6

 and fix with screws and washers 

7

.

Note

: Depending on the sheet thickness of the control cabinet the delivered screws have to be replaced 

by longer ones.

Fixing kit

Application

Article No. Suitable for

Mounting on 
Volumeter OME

UZA 21*

BEM 300/500 / OME 13

UZA 22*

BEM 300/500 / OME 20

UZA 23

BEM 300/500 / OME 24

UZA 24

BEM 300/500 / OME 32

* Not suitable for OME with DIN flanges.

Adapter set

Application

Article No. Suitable for

□

Mounting in the 
control cabinet

□

Conversion of BEM 
4U to BEM 300/500

EGT 23

BEM 300
BEM 500

Scope of delivery:

□

1 sheeting bonded to seal

□

1 sheeting

1

Electronic unit

2

Front frame*

3

Sheeting bonded to seal**

4

Control cabinet

5

Sheeting**

6

Sealing frame*

7

Screws and washers*

*    Part of the scope of delivery of BEM 300/500

** Adapter set

1

2

3

4

5

6

7

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands