kozy heat CHASKA CSK-335S Installation And Operation Manual Download Page 31

This limited 10 Year Warranty will not become effective until the Warranty Registration Form has been completed and mailed to Hussong 
Manufacturing Co., Inc., P.O. Box 577, Lakefield, MN 56150. This registration form must be received within 30 days of installation. Failure to do so 
may result in delayed warranty coverage and submission of proof of purchase will be required. 
 
Hussong Manufacturing Co., Inc. warranties to the original purchaser of this Kozy Heat Fireplace, that it is free of defects in materials and 
workmanship at the time of manufacture. 
 
Subject to the following conditions & requirements, Hussong Manufacturing Co., Inc. extends the following limited warranty under normal use and 
service, with respect to the Kozy Heat line of gas burning fireplaces. 

Effective December 2014 

Year 1 

Subject  to  the conditions  &  requirements  listed  below,  within the first  year from  date  of  purchase,  Hussong  Manufacturing  Co.,  Inc. shall,  at  its 
discretion,  replace  or  repair  any such  defect  in  material  or  workmanship,  at  Hussong  Manufacturing  Co., Inc.’s  expense,  including reasonable 
labor costs to repair or replace the defective component, if a factory pre-authorization is given for the repair. 

 

Subject  to  the  conditions  &  requirements  listed  below,  beginning  with  the  first  day  of  the  second  year  and  continuing  through  the  tenth  year, 
Hussong  Manufacturing  Co.,  Inc.,  will  at  its  discretion,  provide  repair  or  replacement  parts  at  current  list  prices  for  any  defect  in  material  or 
workmanship  of  components,  including  optional  components  and  accessories  (if  available).  Hussong  Manufacturing  Co.,  Inc.  shall  not  be  
responsible for any installation, labor, transportation of other indirect costs.

 

Years 2 through 10 

To make a claim under this warranty, the purchaser must first contact the dealer/installer from whom the fireplace was purchased. 
 
This limited warranty will be void if the fireplace is not installed by a qualified installer and according to the installation instructions. Use of 
unauthorized components will make this warranty null and void. 

 

 
This limited warranty also is void if the fireplace is not operated, at all times, according to the operating instructions furnished. 
 
This warranty is limited to defects in material and workmanship. It does not apply to any product that has been subject to negligence, 
misapplication, improper installation. 

 

 
No person is authorized to extend the time of this warranty or to accept on Hussong Manufacturing Co., Inc.’s behalf any additional obligation of 
liability connected with the unit. 

 

 
It is expressly agreed and understood that this warranty is Hussong Manufacturing Co., Inc.’s sole obligation and purchaser’s exclusive remedy for 
defective fireplace equipment. Hussong Manufacturing Co., Inc. shall not be liable for any consequential, incidental or contingent damages 
whatsoever. The foregoing warranty is exclusive and in lieu of all other expressed warranties. Hussong Manufacturing Co., Inc. shall not be held to 
implied warranties or merchantability and fitness for a particular purpose. This warranty replaces all previous warranty policies. 

 

 
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so 
the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which 
vary from state to state. 

 

 
Hussong  Manufacturing Co., Inc. reserves the right to make changes at any time, without notice, in design, material, specifications and prices. 
Hussong Manufacturing Co., Inc. reserves the right to discontinue models and products. 

1. 

You are the original purchaser. This warranty is not transferable. 

2. 

Installation of the fireplace is performed by a qualified installer. 

3. 

Installation and operation must comply with installation and operation instructions. 

4. 

Paint and glass gaskets are covered for 30 days from date of purchase. 

5. 

Remote controls and all optional accessories are covered for 1 year from date of purchase. 

6. 

This warranty does not offer coverage for Light Bulbs, Batteries or Fuses (whether factory, dealer or installer supplied). This includes any 
damage stemming from either component’s nonuse. 

7. 

Components  broken,  (including  glass  panels),  during  shipping,  careless  handling  of  components,  or  defects  resulting  from  improper 
installation, misuse of the fireplace and components are not covered under this warranty. 

8. 

This warranty does not cover any part of the fireplace or any components which have been exposed to or submerged underwater.  

9. 

Hussong Manufacturing Co., Inc. must be notified by the dealer the fireplace was purchased from or a qualified installer/service technician of 
the defect.  

10.  Annual service of the fireplace as required in the installation manual, is performed by a qualified installer/service technician. 

  

(Copies of such service records may be required to claim a warranty).  

11.  All previous warranty/service has been performed by a qualified installer or service technician.    

(Copies of such service records may be required to claim a warranty). 

LIMITED WARRANTY 

Kozy Heat Limited 10 Year Warranty 

Limitation of Liability 

Warranty Conditions and Requirements 

29 

Summary of Contents for CHASKA CSK-335S


































Reviews: