background image

VII. Specific Model Data

Mounting

Kooltronic Air Conditioners have been engineered to be installed easily. To avoid damaging your Air
Conditioner, please read the following information before installation:

1.

Remove and save the four screws holding the Mounting Template and Assembly Bracket
(M/TAB) to the unit. Remove the M/TAB.

2.

See Figure 1 for proper M/TAB orientation.Place the M/TAB flush against the outside of the
cabinet to locate cutouts and mounting holes.

3.

NOTE: The top cutout for the warm air return does not have to match the full 9" opening on
the M/TAB.You can locate your cutout anywhere within this opening. Locate your cutout close
to the top and not less than 3" high. Make sure the cutouts don't interfere with components
inside your cabinet.

4.

Mount the M/TAB to the outside of the cabinet using all the mounting hardware supplied by
Kooltronic (

1/

4

-20 screws/nuts/washers). NOTE: Make sure the screws are inserted with heads

on M/TAB side. Tighten nuts securely.

5.

Route the power cord through the top cut out in your cabinet. Mount the unit to the M/TAB by
sliding the studs located on each side panel into the slots on the M/TAB.

6.

Insert the remaining 10-32 screws and seal washers supplied by Kooltronic through the Air
Conditioner side panel and into the M/TAB. To avoid misalignment of parts do not tighten any
of the screws until they are all installed. Be careful not to overtighten the screws.

7.

Attach overflow drain hose supplied to the drain exit in the side or bottom of the unit.This hose
must not be elevated above the exit port. Improper mounting will impede the flow of conden-
sate and may cause internal malfunctions.

CAUTION

If the Air Conditioner is mounted to the cabinet door you must be sure

that the door hinges will support the additional weight of the Air

Conditioner. Also be certain that when the door is opened fully, the

cabinet does not become unbalanced. The actual weight of the unit can

be found in the performance specifications.

7

Dimensions (inches) are for reference only and are subject to change.

MOUNTING PLAN

POWER
CORD

THERMOSTAT
ADJUSTMENT

FILTER

M/TAB

12

1/

2

32

7/

8

9

1/

2

12

3/

8

11

3/

16

10

1/

2

(8)

.312 DIA.

HOLES

8 TYP.

7

3/

8

9

1/

8

3/

8

2

3/

4

19

5/

8

9

32

7/

8

9/

16

15/

16

1

5/

8

COOL AIR OUTLET
TO ENCLOSURE

WARM AIR RETURN
FROM ENCLOSURE
(Enclosure opening should be located as
high as possible within this area, and equal
or exceed size of cool air outlets.)

CONDENSER OUTLET
(Warm Ambient Air Out)

FILTERED
CONDENSER AIR INLET
(Ambient Air In)

FIGURE 1

Summary of Contents for TRIMLINE K2A3C5NP33L















Reviews: